Publicidad
Enlaces rápidos
MOUNT KIT
1342B
ITEM
QTY
1
1
SAFARI BAR ASSEMBLY (PURCHASED SEPARATELY)
2,3
2
BRACKET, PASSENGER (2) AND DRIVER (3)
4
2
1/2-13 X 2.00" HEX HEAD BOLT
5
4
1/2" FLAT WASHER
6
2
1/2" LOCK WASHER
7
2
M8-1.25 X 25MM HEX HEAD BOLT
8
2
8MM FLAT WASHER
9
2
8MM LOCK WASHER
10
2
M6-1.00 X 25MM HEX HEAD BOLT
11
2
6MM FLAT WASHER
12
2
6MM LOCK WASHER
1
1
BARRA PARA PARRILLA SAFARI (SE COMPRA SEPARADO)
2,3
2
SOPORTE, ACOMPAÑANTE
4
2
PERNOS CON CABEZA HEXAGONAL DE 1/2-13 X 2,00"
5
4
ARANDELAS PLANAS SAE DE 1/2"
6
2
ARANDELAS DE PRESIÓN DE 1/2"
7
2
PERNOS CON CABEZA HEXAGONAL M8-1,25 X 25 MM
8
2
ARANDELAS PLANAS DE 8MM
9
2
ARANDELAS DE PRESIÓN DE 8MM
10
2
PERNOS CON CABEZA HEXAGONAL M6-1,00 X 25 MM
11
2
ARANDELAS PLANAS DE 6MM
12
2
ARANDELAS DE PRESIÓN DE 6MM
1
1
MONTAGE DE LA BARRE PARE-CHOCS SAFARI (ACHETE SEPAREMENT)
2,3
2
SUPPORTS, PASSAGER (2) ET CONDUCTEUR (3)
4
2
BOULON A TETE HEXAGONALE DE 1/2-13 X 2,00 PO
5
4
RONDELLE PLATE 1/2 PO
6
2
RONDELLE A FREIM DE 1/2 PO
7
2
BOULONS A TETE HEXAGONALE M8-1,25 X 25MM
8
2
RONDELLE PLATE 8MM
9
2
RONDELLE FREIN 8MM
10
2
BOULONS A TETE HEXAGONALE M6-1,00 X 25MM
11
2
RONDELLE PLATE 6MM
12
2
RONDELLE FREIN 6MM
STEP 1.
Remove the contents from box and check for damage. Verify all parts are present. Read instructions
completely before beginning.
.
STEP 2
Remove six 6mm hex head bolts with 10mm socket and two plastic push pins (near center) with screw
driver so that plastic shroud can be moved to access front frame cross member.
.
STEP 3
Determine passenger and driver brackets.
bolts previously removed.
STEP 4.
Attach brackets to cross member using metric fasteners as shown. Recommended torque value is 23 Ft.
Lbs. for 8mm fasteners. Leave 6mm fasteners loose.
STEP 5.
Trim a notch in plastic shroud to clear back side of brackets on each side so that it can be re-fastened.
STEP 6.
Remove 6mm fasteners from brackets and reinsert with plastic shroud in place. Replace four factory
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2001-05 TOYOTA RAV-4
APLICACIÓN: TOYOTA RAV-4, MOD. 2001-05
APPLICATION: TOYOTA RAV-4 2001-05
1
CONTENTS -
CONTENIDO
(2)
Y EL CONDUCTOR
- CONTENU
(3)
NOTE:
Brackets line up with farthest outside 6mm hex head
2
3
TOOLS -
HERRAMIENTA
3/4" SOCKET
13MM SOCKET
10MM SOCKET
3" EXTENSION
RATCHET
SMALL FLAT SCREWDRIVER
TORQUE WRENCH
UTILITY KNIFE
DADO DE 3/4"
DADO DE 13MM
DADO DE 10MM
EXTENSIÓN DE 3"
MANERAL
DESTORNILLADOR DE PUNTA PLANA
PEQUEÑO
LLAVE DE TORQUE
NAVAJA
DOUILLE 3/4 PO
DOUILLE 9/16 PO
DOUILLE 13MM
DOUILLE 10MM
RALLANGE 3 PO
CLIQUET
PETIT TOURNEVIS A BOUT PLAT
CLE DE COUPLE
COUTEAU
- OUTILS
Publicidad
Manuales relacionados para Vanguard 1342B
Resumen de contenidos para Vanguard 1342B
- Página 1 INSTRUCTIONS-INSTRUCCIONES-CONSIGNES APPLICATION: 2001-05 TOYOTA RAV-4 APLICACIÓN: TOYOTA RAV-4, MOD. 2001-05 APPLICATION: TOYOTA RAV-4 2001-05 MOUNT KIT 1342B ITEM CONTENTS - CONTENIDO - CONTENU TOOLS - HERRAMIENTA - OUTILS SAFARI BAR ASSEMBLY (PURCHASED SEPARATELY) 3/4” SOCKET BRACKET, PASSENGER (2) AND DRIVER (3) 13MM SOCKET 1/2-13 X 2.00”...
- Página 2 NOTE: 6mm hex head bolts and plastic push pins though remaining holes in plastic shroud. Factory 6mm hex head bolts with shoulder go though plastic bumper tabs. Recommended torque value is 9 Ft. Lbs. for 6mm fasteners. STEP 7 Attach Safari Bar to mount brackets using 1/2” fasteners. Level and adjust Safari Bar as desired and PASO 1.
- Página 3 FRONT, FRAME CROSS MEMBER FRONT, FRAME CROSS MEMBER DELANTERA, PIEZA TRANSVERSAL DE LA CARROCERÍA DELANTERA, PIEZA TRANSVERSAL DE LA CARROCERÍA TRANSVERSALE AVANT DU CADRE TRANSVERSALE AVANT DU CADRE FIGURE 1 FIGURA 1 FIGURE 1 FIGURE 1 FIGURA 1 FIGURE 1 INSTALLATION VIEW OF PASSENGER SIDE, DRIVER SIDE OPPOSITE INSTALLATION VIEW OF PASSENGER SIDE, DRIVER SIDE OPPOSITE VISTA DE LA INSTALACIÓN DEL LADO DEL ACOMPAÑANTE OPUESTO AL LADO DEL CONDUCTOR...