Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
The Vega self-aligning photocell is a safety device comprising modulated infrared Transmitter and Receiver. Breaking the
path of the beam causes a switch in the status of the electric contact on the Receiver.
P
o
w
r e
u s
p
p
y l
A
b
s
r o
t b
o i
n
S
e
s n
n i
g
a r
n
g
e
P I
O
b
s
a t
c
e l
d
e
e t
t c
o i
n
i t
m
e
IMPORTANT NOTICE
•Warning! In order to ensure personal safety, it is important that all instructions be carried out to the letter.
Incorrect installation or use of product could cause serious personal injury.
•Before attempting installation, read the instructions carefully and store in a safe place for future reference.
1. FITTING
• In order to ensure optimum working efficiency, the Receiver and Transmitter should be properly aligned.
IMPORTANT: Due to the self-alignment feature, it is not possible to install two pairs of VEGA on the same system.
In such cases ORION should be used.
Two types of installation are possible:
1- Wall with embedded tube (fig.1).
2- With outer tube/sheath (fig.2).
•Carry out the work necessary for the electrical connections.
•Fix the Vega enclosures using suitable screws and screw anchors.
2. ELECTRICAL CONNECTIONS
•Effect the electrical connections on terminal blocks of Receiver (fig.4) and Transmitter (fig.5) using the cable duct
supplied.
•Connect wiring to the electronic control unit and any other photocells present in the system.
• Refer to the diagrams contained in the electronic control unit instructions for details of the various configurations.
3. START-UP
• Power up photocells and check that LED DL1 on the Receiver (fig.4) and Transmitter (fig.5) is lit.
• Assemble Vega using the components supplied (fig.6).
• Ensure correct alignment by checking against the light that LED DL2 on the Receiver (fig. 4) is also lit.
Manufacturer:
GENIUS S.p.A.
Address:
Via Padre Elzi, 32 - 24050 - Grassobbio- Bergamo - ITALY
Declares that:
The active optoelectronic safety device model VEGA
• conforms to the essential safety requirements of the following EEC directives:
73/23/EEC and subsequent modification 93/68/EEC.
89/336/EEC and subsequent modification 92/31/EEC and 93/68/EEC
Additional note:
This product was tested in a typical, uniform configuration (all products made by GENIUS S.p.A.)
Grassobbio, 08-02-2006
ENGLISH
2
4
V
D
C
/
2
4
V
A
C
x T
=
2
0
m
A
R
x
=
3
0
m
A
2
0
m
5
4
1
3
m
S
e
c
CE DECLARATION OF CONFORMITY
C
o
n
a t
t c
y t
p
e
a
n
d
r
t a
y T
p
e
f o
l a
g i
n
m
e
t n
S
e
- f l
l a
g i
n
m
e
t n
a
n
g
O
p
r e
t a
n i
g
a
m
b
e i
t n
e t
m
p
e
a r
u t
e r
I
s n
a t
l l
t a
o i
n
3 3 3 3 3 3
n i
g
N
C
6
0
V
A
/
a
u
o t
m
t a
c i
+
- /
° 7
2 (
0
m
e l
+
- /
1
, 3
° 5
5 (
2 -
° 0
C
/
+
5
° 5
w
a
- l l
m
o
u
t n
n i
Managing Director
D. Gianantoni
2
4
W
)
m
)
C
g
Publicidad
Tabla de contenido
