Black and Decker 375 AMP Manual De Instrucciones página 5

• Excessive engine cranking can damage the vehicle's starter motor. If the engine fails to start after the
recommended number of attempts, discontinue jump-start procedure and look for other problems
that need to be corrected.
• After use, turn the Jump-Starter power Switch OFF.
• Replace worn or defective parts immediately — contact the Customer Service Department toll free
1-877-571-2391.
PoRTABlE CoMPRESSoR
The built-in 12 volt DC compressor can be used to inflate all vehicle tires and recreational inflatables.
An compressor nozzle, sports needle and bicycle racing tire adapter (presta Stem Adapter) are
included. Each one of these compressor adapters connect to the compressor chuck at the end of the
hose. The compressor adapters can be stored inside the compressor compartment on the back of the
unit. The Compressor power Switch is located on the front of the unit near the pressure gauge. The
Air pressure Gauge is located on the front of the unit above the control panel. The compressor can
operate long enough to fill up to 3 average sized tires before the battery must be recharged.
The compressor may be used by removing the air hose from the storage hatch and if required, fitting
an appropriate nozzle to the air hose. Return hose to the storage compartment after use.
WARNING: BURST HAZARD
• The compressor is capable of inflating up to 120 pounds per square inch (psi) pressure. To avoid
over-inflation, carefully follow instructions on articles to be inflated. Never exceed recommended
pressures. Bursting articles can cause serious injury.
• Always check pressure with the pressure gauge.
• Never leave the compressor unattended while in use.
CAUTION: RISK OF PROPERTY DAMAGE
Do not operate compressor continuously for extended periods of time (approximately 10 minutes,
depending on ambient temperatures), as it may overheat. In such event, compressor will automatically
shut down. Immediately turn OFF the Compressor power Switch. Restart after a cooling down period
of approximately 30 minutes.
Inflating Tires or Products With Valve Stems
1. Lift the thumb latch on the nozzle (chuck) and fit it onto the valve stem.
2. Ensure the nozzle connector is pushed on to valve stem as far as possible before closing thumb
latch.
3. Make sure latch is secure.
4. Slide the Compressor power Switch to the on position.
5. Monitor the current pressure on the gauge.
6. When desired pressure is reached, open thumb latch and remove the nozzle connector from the
valve stem.
7. Slide the Compressor power Switch to the off position.
8. Allow unit to cool before storing away.
9. Store compressor hose and tire fitting in storage compartment.
Inflating other Inflatables Without Valve Stems
Inflation of other items requires use of one of the adapters (nozzles).
1. Select the appropriate adapter nozzle.
2. Lift the thumb latch on the nozzle, insert the adapter (i.e., needle) into the nozzle connector and
close thumb latch.
3. Insert adapter (i.e., needle) into item to be inflated.
4. Slide the Compressor power Switch to the on position.
5. Monitor the current pressure on the gauge.
IMPORTANT NOTE: Small items such as volleyballs, footballs, etc. inflate very rapidly. Do not over-
inflate.
6. When desired pressure is reached, open thumb latch and remove connector from valve stem.
7. Remove adapter.
8. Slide the Compressor power Switch to the off position.
9. Allow unit to cool before storing away.
10. Store compressor hose and tire fitting in storage compartment.
WARNING: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE: FOLLOW ALL SAFETY
INSTRUCTIONS FOUND IN THIS INSTRUCTION MANUAL.
JUS375IB_ManualENSP_091211.indd 8-9
8
USB PoWER PoRT
1. push the USB power port On/Off Switch to turn the USB port ON. The USB power On Indicator
will light to indicate the USB power port is ready to use.
2. Lift up the cover of the USB power port.
3. plug the USB-powered device into the USB power port and operate normally.
periodically check the unit's battery status by pressing the Battery Charge Level Button.
Notes:
This unit' s USB Power Port does not support data communication. It only provides 5 volts/500mA DC power to an external USB-
powered device. Make sure the USB Charging Port ON/OFF Pushbutton is in the OFF position when the unit is being recharged or
stored.
Some household USB-powered electronics will not operate with this unit.
12 VolT DC PoRTABlE PoWER SUPPly
This portable power source is also for use with all 12 volt DC accessories equipped with a male
accessory outlet plug and are rated up to 5 amps.
1. Lift up the cover of the unit's 12 volt DC outlet.
2. Insert the 12 volt DC plug from the appliance into the 12 volt accessory outlet on the unit. DO NOT
EXCEED A 5 AMp LOAD.
3. Switch on the appliance and operate as usual.
periodically check the unit's battery status by pressing the Battery Charge Level Button.
EMERGENCy AREA lIGHT
The area light is controlled by the Area Light power Switch on the front panel of the unit. Make sure
the lamp is turned OFF when the unit is being recharged or stored.
periodically check the unit's battery status by pressing the Battery Charge Level Button.
TRoUBlESHooTING
Solution
Problem
Unit will not charge • Make sure all power switches are in the OFF position.
• Make sure a suitable gauge extension cord is properly
connected to both the unit and a functioning AC outlet.
Unit fails to Jump-Start • Make sure unit's power switch is in the ON position.
• Check that Jump-Starter has a full charge. Recharge unit if necessary.
• Make sure a proper polarity cable connection has been established.
• Leave charger plugged in and keep unit on charge for 24-48 hours.
portable Compressor will not • Make sure the Compressor power Switch is in the on position.
inflate • Check that jump-starter has a full charge. Recharge unit if
necessary.
• Make sure connector is pushed to valve stem and thumb latch
is closed when attempting to inflate tires; or nozzle (adapter) is
securely inserted into connector (chuck) on all other inflatables.
12VDC Accessory Outlet will not • Make sure the appliance does not draw more than 5 amps.
power appliance • Check that Jump-Starter has a full charge. Recharge unit if
necessary.
USB power port will not power • Make sure the USB power port ON/OFF pushbutton is in the ON
appliance position.
• Check that Jump-Starter has a full charge. Recharge unit if
necessary.
• Check the rating of equipment plugged into the unit's USB outlet do
not exceed 500mA continuous.
• Some household USB powered electronics will not operate with this
unit's USB outlet. Check the manual of the corresponding electronic
device to confirm that it can be used with this USB outlet.
LED Area Light does not come on • Make sure the LED Area Light ON/OFF button is in the ON
position
• Check that Jump-Starter has a full charge. Recharge unit if
necessary.
9
9/12/2011 2:25:44 PM