Installation Instructions; Location; Piping - Mr. Heater MH125LP Instrucciones De Uso Y Manual Del Usuario

INSTALLATION INSTRUCTIONS

GENERAL:
READ THESE INSTRUCTIONS CAREFULLY. Read and adhere
to these instructions. DO NOT allow anyone who has not
read these instructions to assemble, light, adjust or operate
this heater.
DO NOT attempt to operate the heater with any gas other
than that indicated on the heater nameplate.
For the U.S. and/or Canada, the installation of this appliance must
comply with local and/or Provincial codes or, in the absence of
these codes,
•
Handling of Liquefied Petroleum Gases, ANSI/NFPA 58
•
B149.2 INSTALLATION CODES.
must be inspected before each use and at least annually by a
qualified service person. If the hose for Model MH125LP shows
evidence of excessive abrasion or wear, or if the hose is cut, it
must be replaced prior to the heater being put into operation.
The replacement hose assembly shall be that specified by the
manufacturer. See the parts list.

LOCATION

located on a hard, flat, level surface to minimize the risk of
prevent accidental tipping. DO NOT operate this heater with
the supply cylinder in any other than the upright position.
This appliance must be installed only in locations where the
The installer must inform the owner/operator of this appliance
that precautions must be taken to protect the appliance from
physical damage.
This appliance produces radiant heat. Therefore, it must be located
at least six feet away from any LP-Gas container and must not be
directed toward any LP-Gas container within 20 feet.
The heater must be installed in a location such that it will not be
exposed directly to water spray, rain, and/or dripping water.
Use of this heater in a draft/windy area decreases its efficiency. If
possible, operate the unit in a draft free area.
The appliance area must be kept clear and free from combustible
materials, gasoline and other flammable vapors and liquids.

PIPING

For Model MH125LP (for use with LP-Gas)
This model may be connected to a self-contained LP-Gas
supply system using the hose and regulator assembly
supplied with the appliance, OR, it may be connected to a
permanently installed LP-Gas supply system.
If connected to a self-contained LP-Gas supply system, the
Mr. Heater, Inc. | Portable Propane Radiant Heater
hose assembly must be inspected prior to each use of the
heater. If it is evident that there is excessive abrasion or wear,
or if the hose is cut, it must be replaced prior to the heater
being put into operation.
If connected to a self-contained LP-Gas supply system, the
cylinder must have no less than a minimum capacity of
40 pounds and no more than a maximum capacity of 100
pounds of LP-Gas. DO NOT connect this appliance to a
cylinder having less than a nominal 40 pounds capacity of
LP-Gas.
WARNING
NEVER USE A FORK LIFT TRUCK TYPE
CYLINDER.
The connection of Model MH125LP to an LP-Gas cylinder must
be made in a well ventilated area using the regulator and hose
assembly supplied with the appliance. DO NOT attempt to
adjust this regulator. It has been preset at the factory to provide
to the LP-Gas cylinder. Turn the POL nut in a counter-clockwise
compound on POL threads.
The heater must be located at least six feet away from any
LP-Gas cylinder and must not be directed toward any LP-Gas
cylinder within 20 feet. If more than one heater is used, they
and the supply cylinders must be separated by at least 20
feet. Check local codes.
The gas supply must be turned off at the LP-Gas supply
cylinder when the heater is not in use.
When the heater is to be stored indoors, the connection
between the LP-Gas supply cylinder and the heater must be
disconnected and the cylinder removed from the heater and
stored in accordance with Chapter 5 of the Standard for the
Storage and Handling of Liquefied Petroleum Gases. ANSI/
If connected to a permanently installed LP-Gas supply system,
the system requires the use of a two-stage gas regulator
assembly which is normally provided by your LP Gas dealer
as part of the LP-Gas supply system. Consult with your local
LP Gas dealer for details concerning proper equipment and
installation.
Before attempting to ignite the appliance, all gas fittings and
connections must be thoroughly checked for gas leaks. Apply a
small amount of a mild soap and water solution to all fittings and
connections and observe for escaping bubbles. If any leaks are
detected, shut off the gas supply to the appliance immediately.
leakage. Dry all fittings and connections after leak testing.
WARNING
NEVER USE A FLAME FOR GAS LEAK TESTING.
4
DO NOT use pipe