Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24773F
Wrenches: 11/16, 3/4
Drill Bits: 1/2"
j
Qty. (2)
1/2-13 X 1.50 Carriage Bolt
k
Qty. (2)
1/4 X 1.00 X 3.00 Block
l
Qty. (2)
Conical Toothed Washer
m
Qty. (2)
1/2 Hex Nut
Enlarge existing holes on the bottom surface of the vehicle bumper structure with a 1/2" drill bit.
1.
2.
Fishwire carriage bolts and blocks through the vehicle bumper structure and through the 1/2 drilled holes in in step 1.
3.
Raise hitch into position and loosely install the conical toothed washers and 1/2 hex nuts.
4.
Install the 3/8 U-Bolt through the vehicle tow hook and through the tow hook attachment of the receiver. Install lock washers
and 3/8 hex nuts as shown above.
5.
Tighten all remaining fasteners to the required torque specifications.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2006, 2015 Cequent Performance Products, Inc. - Printed in Mexico
Installation Instructions
Fascia
(Sold separately)
Drawbar Kit:
3593
Drawbar must be used in the
Rise position only.
Enlarge Existing
Holes (See Step 1.)
Vehicle Tow Hook
Tighten all 3/8-16 GR5 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)
Tighten all 1/2-13 GR 5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Mazda 5
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, PC4
n
Qty. (1)
3/8-16 U-Bolt
o
Qty. (2)
Lock Washer
p
Qty. (2)
3/8 Hex Nut
Sheet 1 of 3
Part Numbers:
Manufacturer's Rating or
Vehicle Bumper
Structure
24773N
10-13-15
24773
77150
60841
Rev. B
Publicidad
Manuales relacionados para Cequent Performance Products 24773
Resumen de contenidos para Cequent Performance Products 24773
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24773N 10-13-15 Rev. B 2006, 2015 Cequent Performance Products, Inc. - Printed in Mexico...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matiè re de sé curité des systè mes d’attelage. Feuille 2 de 3 24773N 10-13-15 Rev. B 2006, 2015 Cequent Performance Products, Inc. Imprimé au Mexique...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684 Hoja 3 de 3 24773N 10-13-15 Rev. B 2006, 2015 Cequent Performance Products, Inc. - Impreso en México...