Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame Rail
Receiver Shown In Proper Position
Equipment Required:
Fastener Kit: F65030
Wrenches: 8mm, 10mm,
15mm, 7/8"
Drill Bits: None
Frame Rail
Remove Frame Bracket
Reinforcements
1
Qty. (4)
Carriage Bolt, 1/2"-13 x 1-3/4"
2
Qty. (4)
Carriage Bolt, 1/2"-13 x 2-1/4"
3
Qty. (2)
Spacer, 1-1/2" x 2" x 1/4"
1.
Remove plastic air dam.
2.
If present, remove OEM tow hooks and frame bracket reinforcements. Return frame bracket reinforcements to vehicle owner for
reinstallation if receiver is removed.
3.
Remove existing nut & install angle bracket to bumper bolt as shown. Angle bracket must be installed.
4.
Raise receiver into position from below.
VEHICLES WITH OEM TOW HOOKS
5.
Sandwich receiver between frame bracket & tow hook and attach with 2-1/4" carriage bolts provided.
VEHICLES WITHOUT OEM TOW HOOKS
6.
Attach with 1-3/4" carriage bolts provided.
7.
Reinstall air dam.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005 Cequent Towing Products
Front Mounted Receiver
Installation Instructions
Ford Explorer
Ford Sport Trac
Fascia
WITHOUT OEM
TOW HOOKS
Tighten all M10 CL8.8 fasteners with torque wrench to 53 Lb.-Ft (72 N-m).
Tighten all 1/2" GR5 fasteners with torque wrench to 75 Lb.-Ft (102 N-m).
CARGO CAPACITY – DO NOT EXCEED
300 LB. OR VEHICLE FRONT GROSS
AXLE WEIGHT RATING. (GAWR)
9000
Nut (Existing)
Frame Bracket
OEM Tow Hook
WITH OEM
TOW HOOKS
4
Qty. (2)
Angle Bracket
5
Qty. (4)
Conical Washer, 1/2"
6
Qty. (4)
Hex Nut, 1/2"
Sheet 1 of 3
N65030
Part Numbers:
65030
LB. MAX. WINCH LINE PULL
Bumper Bolt
(Existing)
Frame Bracket
11-07-05
Rev. A
Publicidad
Manuales relacionados para Cequent Towing Products 65030
Resumen de contenidos para Cequent Towing Products 65030
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 N65030 11-07-05 Rev. A 2005 Cequent Towing Products...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 N65030 11-07-05 Rev. A 2005 Cequent Towing Products...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 N65030 11-07-05 Rev. A 2005 Cequent Towing Products...