Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 38066F
Wrenches: 19mm, ¾, Torque
Hex Nut 1/2-13
Conical Washer
j
Qty. (4)
Hex Bolt M12
k
Qty. (6)
Conical Washer
l
Qty. (2)
Carriage Bolt 1/2-13
m
Qty. (2)
Hex Nut 1/2-13
1. If present, remove the tie down bracket from vehicle frame rail and discard bolts. Tie down bracket will be re-attached with new hardware.
2. Feed the carriage bolt and block thru slots in side of frame rails using the pull wire.
3. Raise the hitch into position; lifting the bumper mounting bracket over the fascia (where needed). Secure with M12 bolts and conical washers into
the existing weld nuts, being careful not to push the bolts into the frame.
4. Hand tighten all bolts.
5. Tighten all 1/2-13 GR5 fastener with torque wrench to 75 Lb.-Ft. Tighten all M12 CL10.9 fasteners with torque wrench to 75 Lb.-Ft.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005 Cequent Towing Products
Installation Instructions
Toyota FJ Cruiser
Fascia
Carriage Bolt 1/2-13
Pull Wire
Block 1" X 1.5"
Tie Down Bracket
Hex Bolt M12
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location:
n
Qty. (2)
Block 1" X 1.5"
o
Qty. (2)
Pull Wire
p
r
75461N
Part Numbers:
75461
44545
87412
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
6000
600
5000
500
10-13-06
Rev. C
Form: F205 Rev A 5-6-05

Publicidad

loading

Resumen de contenidos para Cequent Towing Products 75461

  • Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2005 Cequent Towing Products Sheet 1 of 3 75461N 10-13-06 Rev.
  • Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2005 Cequent Towing Products Feuille 2 de 3...
  • Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684 2005 Cequent Towing Products Hoja 3 de 3 75461N 10-13-06 Rev.

Este manual también es adecuado para:

4454587412