Packing And Moving; Maintenance; Defrost; Disconnecting The Appliance - MiLECTRIC RFD-214B Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

INSTRUCTION FOR USAGE
The temperature of refrigerator can be controlled manually by the knob. However,
the number shown on the knob does not directly represent the temperature. Instead,
the larger the number is, the lower the interior temperature will be. 0 stands for off. Turn
the knob to state 4 when it is normal used, turn it to the state during 4-7 if a lower interior
temperature is required; contrarily, to the state during 4-1, when a higher one is needed.

PACKING AND MOVING

1.
Unpack , repack and carry
Please memorize the position of each accessory of the appliance
when unpack it, repack the product and check it carefully before
transportation.
2.
Do not lift or pull the door or the door handle during transportation.
3.
When moving, the appliance can not be sloped over 45 degrees
(the angle to the vertical direction). Please avoid strong vibration
and hit.

MAINTENANCE

The appliance should be maintained and cleaned frequently. For your safety,do
please pull the plug out of the socket before the cleaning.
1.
Interior maintenance
Clean the interior of the appliance with clean water or neutral abluent.Scour it with
clean water and wipe it with a piece of dry cloth.
2.
Maintenance of door gasket
It is easy to damage if the door gaskets are polluted by the stain like oil, sauce and
etc., so it is better to clean them carefully.
3.
Outer maintenance
Wipe the dusty with a piece of dry cloth ,clean it with neutral abluentif necessary.
4.
The displacement of interior light Uninstall the cover and replace the light with a
screwing light (E14 , 220V/10W),Consult the following pictures:
①. Pry the bolt on the thermostat
away from the lamp shade about
2mm with the tool.
③.Take out the lamp shade along
4
the direction of the arrow.
②.Meanwhile take another side
as the center to ratote the lamp
shade outwards.
④.Rotate and take out the bulb in
counterclockwise direction.

DEFROST

The heavy frost will influence the refrigerating of the appliance and increase the
energy consumption. Thus, defrosting is needed as the frost is as thick as 5 mm.
Processes of the manual defrost are listed as following: take all the food out of the
compartment; uninstall the drawers and shelves; unplug the electronic power cord;
open the doors and wait for the thaw; wipe up the water with dry cloth.
Do not use any other equipment or method to push the
defrost process. It may destroy the cooling system.

DISCONNECTING THE APPLIANCE

After power failure, even in summer, the refrigerator can store food normally in several
hours.
1.
Discontinuation during power failure
After power failure, do not put additional food in the appliance and reduce the frequency
of door opening.Make several ices in a container if know the power failure beforehand,
and put it in the top of the fridge.
2.
Discontinuation during vacation
Please fetch out the easy-rot food and the food in fridge before shot vacation. After
confirmation, close the door firmly.If have a long vacation, please fetch out all the food
and cut off the power. After defrosting, clean up the liner of the appliance and wipeit dry,
and leave the door open.
3.
Stop using
If the refrigerator may be stopped using for a long time, please unplug the outlet and
clean up the appliance. The door should be kept open in order to prevent unpleasant
smell caused by food leavings.
In a general condition, do not stop the appliance in case of affecting
its life. After unplugging the power, please leave at least 5 minutes
Attention
before resumption.

USER NOTIFICATIONS

1.
Do not splash water on the refrigerator, as it will cause oxidation and malfunction.
Electronic component such as on/off button should be wiped dryly.
2.
Cleansers such as soap powder, abrasive cleaning powder, alkali cleansers, chemical
cloth, thinner, alcohol, acid petroleum productand hot water should not be used to
clean the refrigerator as they may damage the painted cover and plastics.
3.
Smear can damage the interior plastic component, so wipe it as soon as possible.
5

Publicidad

Tabla de contenido
loading

Tabla de contenido