Remote Control - Revell Control BLUESHOT Manual Del Usuario

The model is equipped with a
rechargeable lithium polymer
battery. Please observe the following
safety instructions:
• Never throw LiPo batteries into a fire
or store them in a hot location.
• Only use the supplied charger to
charge the battery. The use of a
different charger may lead to the
permanent damage of the battery
and neighbouring parts, as well as
physical injury!
• Never use a charger for NiCd/NiMH
batteries!
• Always ensure that the charging
process takes place on a fireproof
surface in a fire-resistant environment.
• Do not leave the battery unsupervised
during the charging process.
• Never disassemble or alter the battery
contacts. Do not damage or puncture
the battery cells. There is a risk of
explosion!
• The LiPo battery must be kept out of
reach of children.
• When disposing of batteries, they
must be discharged or their capacity
must be fully depleted. Cover exposed
terminals with adhesive tape in order
to prevent short-circuiting!
1A Camera 1E Camera lens
1B Battery plug 1F Battery connection
cable
1C Rotors
1G ON-OFF switch
1D Fuselage cover
16
Maintenance and care:
• Please only use a clean, damp cloth
to wipe off the model.
• Protect the model and batteries from
direct sunlight and/or direct heat.
• Never allow the remote control and
charging unit to come into contact
with water, because the electronics
will be damaged as a result.
Technical changes and differences in
color reserved!
Required batteries for the model:
Power supply:
Rated output: 1 x DC 3,7 V / 2 Wh
Batteries: 3,7 V rechargeable
LiPo battery (included)
Capacity: 550 mAh
Battery requirement for the

remote control:

Power supply:
DC 9 V Batteries:
6 x 1.5 V "AA"
(not included)
USB charger:
Power supply: DC 5V via USB port,
500 mA or higher
Rated output: 5 V / 500 mA max.
1 modEl
1H SD card slot
2 rEmotE control
2A Trim for rotation
2B No function
2C Control for thrust and rotation
2D Video button
2E Power LED
2F Antenna
2G Turbo switch
2H Flip button
3 insErting battEriEs (rEmotE control)
3ATo open the battery 3B Insert 6 x 1.5 V AA batteries
compartment, unscrew and pay attention to the
the locking screw (2N) polarity specifications, as
counter-clockwise and indicated in the battery
compartment.
open the battery
compartment cover (2M)
to the top by pressing
down the opening lever
(2O).
4 charging thE modEl
Attention: The battery and motor must cool down for 15 to 30 minutes before
charging and after every flight. Otherwise they can be damaged. The charging process
must be constantly monitored. Always ensure that the charging process takes place on
a fireproof surface in a fire-resistant environment.
• Unplug the battery plug (1B) from the battery connection cable (1F) and switch off
the remote control. Plug the USB charger (4A) into a free USB port. The status LED on
charger now lights up.
• Plug the battery plug (1B) into the charging socket of the charger, ensuring correct
polarity (4B). The battery must be gently inserted into the charging socket – DO NOT
USE FORCE. If the battery is not correctly inserted into the charging socket, the battery
may become damaged and, under certain circumstances, cause injury.
• The status LED on the USB charger goes out when the charging process starts.
The red LED on the charger lights up as soon as the charging process is finished.
• The charging process lasts approx. 80 minutes and must be continuously monitored.
The red LED on the charger lights up as soon as the charging process is finished.
• Disconnect the battery from the charger and disconnect the charger from the USB
port once charging is complete.
The model can fly for approx. 4-6 minutes after a charge time of approx.
80 minutes.
Warning notice: The battery does not normally heat up while charging. If it should
become warm or even hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
2I Control for forwards/backwards and
sideways flight
2J Trim for forwards/backwards
2K Trim for sideways
2L ON/OFF switch
2M Battery compartment cover
2N Locking screw
2O Opening lever for the battery
compartment
3C Close the battery
compartment cover
and screw in the
locking screw (2N)
clockwise.
17