Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Vehicle tie
down bracket
Fascia
Hitch Shown In Proper Position
Equipment Required: Pliers, small flat screwdriver
Fastener Kit: 24911F
Wrenches: 9/16" open end wrench,
11/16" & two 15/16"
Drill Bits: None
p
o
m
p
l
o
j
Qty. (2)
Bolt 5/8-11 X 2.0 GR8
k
Flat washer 5/8"
Qty. (2)
l
Lock washer 5/8"
Qty. (2)
m
Qty. (2)
Hex nut 5/8-11
1.
Locate a tab at the bottom center of the trunk pan, bend down and out of the way.
2.
Remove the (2) plastic rivets that fasten the fascia tabs to the vehicle. Note: Remove the center of the rivet with a flat screwdriver. Keep for re-
installation.
3.
Raise hitch into position passenger side first. Slide hitch under the fascia tab and over the top of the exhaust being careful not to scratch the
fascia.
Slide the hitch under the fascia tab on the drivers side and into location between the vehicle's tie down brackets.
4.
5.
Install the 5/8 bolts and flat washer to the outside of the tie down bracket, both sides as shown. Attach the lock washers and hex nuts. (Do not
tighten at this time.)
6.
Install remaining fasteners as shown, both sides.
7.
Tighten all fasteners to the required torque specification.
8.
Re-install the plastic rivets.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2013,, 2015 Cequent Performance Products
Printed in Mexico
Installation Instructions
Toyota Yaris Hatchback
(Sold separately)
Drawbar Kit:
3593
Drawbar must be used in the
RISE position only.
n
Note: Fasteners typical
k
n
j
Tighten all 5/8-11 Gr8 fasteners with torque wrench to 212 Lb.-Ft. (287 N*M)
Tighten all 3/8-16 Gr8 fasteners with torque wrench to 45 Lb.-Ft. (61 N*M)
Bend tab down out of
the way – as shown
both sides
n
Qty. (4)
Bolt 3/8-16 X 1.50 Gr8
o
Lock washer 3/8"
Qty. (4)
p
Qty. (4)
Hex nut 3/8-16
Sheet 1 of 3
24911N
Part Numbers:
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, 4
Vehicle tie down
bracket – both sides
10-05-15
Form F206 Rev B 9-17-2012
24911
60343
77298
Rev. B
Publicidad
Manuales relacionados para Cequent Performance Products 24911
Resumen de contenidos para Cequent Performance Products 24911
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2013,, 2015 Cequent Performance Products Sheet 1 of 3 24911N 10-05-15 Rev.
- Página 2 Instructions d’installation Numé ros de piè ce : Support d’arrimage du véhicule 24911 Caré nage Toyota Yaris Hatchback 60343 (Vendu sé paré ment) 77298 Ensemble de barre de remorquage : 3593 Ne pas excé der les spé cifications de poids du fabricant du vé...
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehí culo y use protecció n visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684. 2013, 2015 Cequent Performance Products Hoja 3 de 3 24911N 10-05-15 Rev.