Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Vehicle
Frame end
Vehicle suspension
mount.
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 36546F
Wrenches: 13mm, 3/4", 7/8"
Use (3) spacer
washers per side,
between hitch and
.
vehicle attachment
7
1
Remove existing inner
tailpipe hanger 8mm bolts,
and replace with supplied
8mm bolts.
1 1 1 1
Qty. (2)
Hex Bolt, M8 x 1.25 x 55mm CL 9.8
2 2 2 2
Qty. (6)
Flat Washer 1/2"
3 3 3 3
Qty. (1)
Hex Bolt, 1/2"-13 x 2-1/4" GR 5
4 4 4 4
Qty. (3)
Conical Toothed Washer, 1/2"
5 5 5 5
Qty. (1)
Hex Nut, 1/2"-13 GR 5
Remove existing inner tailpipe hanger 8mm bolts, and replace with supplied 8mm bolts (item 1).
1.
2.
Install forward bracket as shown. Do not tighten at this time.
3.
Install three flat washers (item 2) on existing weldnut on each side. See Figure 2.
4.
Raise hitch into position. Install over the 8mm bolt and existing weldnut sandwiching the flat washers between vehicle frame and hitch bar. Install 3/8" conical
and M8 hex nut. Do not tighten bolts yet.
5.
Attach the hitch to the hitch bracket.
6.
Tighten fasteners to required specification.
Note: Check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water
and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection.
Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
z 2014, 2015 Cequent Performance Products , Inc. Printed in Mexico
Bumper
Fascia
Drawbar must be used in the
Rise position only.
Vehicle suspension
mount.
5
6
4
Slide handle nut through opening
2
in bottom of suspension mount.
Figure 1.
8mm bolt to replace (step 1).
Tighten 8mm-1.25 CL 9.8 bolts with torque wrench to 25 Lb.-Ft. (34 N*M)
Tighten 1/2"-13 GR 5 bolts with torque wrench to 75 Lb.-Ft. (102 N*M)
*Tighten 1/2"-13 GR 5 bolts into handle-nut to 50 Lb.-Ft. (68 N*M).
Installation Instructions
Buick LaCrosse
(Sold separately)
Drawbar Kit:
36061
Hitch type
Weight Carrying
Ball Mount
Wiring Access Location:
4
9
Hitch forward bracket.
8
4
3
Tailpipe hanger.
6 6 6 6
Qty. (2)
7 7 7 7
Qty. (2)
8 8 8 8
Qty. (1)
9 9 9 9
Qty. (1)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
3500 (1589 Kg)
PC1,2
Vehicle forward
*
1
2
7
6
Hex Nut, M8 x 1.25 CL 10
Conical Toothed Washer, 3/8"
Handle-Nut, 1/2"
(*Torque Spec Below)
Hex Bolt, 1/2"-13 x 1-1/2" GR 5
36546N
10-9-15
Part Numbers:
36546
90240
06167
Max Tongue
WT (LB)
300 (136 Kg)
Existing
weldnut.
Figure 2.
Rev. B
Form: F205 Rev A 5-6-05
Publicidad
Manuales relacionados para Cequent Performance Products 36546
Resumen de contenidos para Cequent Performance Products 36546
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. z 2014, 2015 Cequent Performance Products , Inc. Printed in Mexico Sheet 1 of 3...
- Página 2 Ne jamais utiliser une torche pour découper un accès ou un trou de fixation. Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. z 2014, 2015 Cequent Performance Products, Inc. Imprimé au Mexique Feuille 2 de 3...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 36546N 10-9-15 Rev. B z 2014, 2015 Cequent Performance Products, Inc. Impreso en México Form: F205 Rev A 5-6-05...