Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Receiver Shown In Proper Position
Equipment Required:
Fastener Kit: K65009
Wrenches: 15mm, 7/8"
Drill Bits: 1/2"
Hammer
Swaybar Bracket
1
Qty. (4)
Hex Bolt, M10 x 1.50 x 35
2
Qty. (4)
Conical Washer, 3/8"
3
Qty. (2)
Carriage Bolt, 1/2"-13 x 2-1/4"
4
Qty. (2)
Spacer, 1-1/2" x 2" x 1/4"
5
Qty. (2)
Spacer, 1" x 2" x 7/16"
1.
If present, remove steel skid shield and return to vehicle owner.
2.
Remove lower fascia or trim to clear receiver. CONSULT VEHICLE OWNER BEFORE TRIMMING.
3.
Lower swaybar bracket on each frame rail.
4.
Raise hitch into position and loosely reinstall swaybar bracket as shown above. NOTE: The lip on the underside of the frame rail may need
to be flattened so block can be installed.
5.
Using the receiver as a template drill a 1/2" hole as shown above.
6.
Feed the remaining fasteners as shown above through slot in the end of the frame rails using pull wire.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005 Cequent Towing Products
Front Mounted Receiver
Installation Instructions
Jeep Cherokee, Comanche,
Wagoneer (Downsize)
Bumper
Lower
Fascia
Existing Weldnuts
Drilled Hole
Tighten all M10 CL10.9 fasteners with torque wrench to 42 Lb.-Ft (57 N-m).
Tighten all 1/2" GR5 fasteners with torque wrench to 75 Lb.-Ft (102 N-m).
CARGO CAPACITY – DO NOT EXCEED
300 LB. OR VEHICLE FRONT GROSS
AXLE WEIGHT RATING. (GAWR)
9000
Recovery
Eye
6
Qty. (2)
Flat Washer, 1/2"
7
Qty. (2)
Lock Washer, 1/2"
8
Qty. (2)
Hex Nut, 1/2"
9
Qty. (2)
Pull Wire
Sheet 1 of 3
N65009
Part Numbers:
65009
LB. MAX. WINCH LINE PULL
Frame Rail
Slot
Lip
11-07-05
Rev. A
Publicidad
Manuales relacionados para Cequent Towing Products 65009
Resumen de contenidos para Cequent Towing Products 65009
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 N65009 11-07-05 Rev. A 2005 Cequent Towing Products...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 N65009 11-07-05 Rev. A 2005 Cequent Towing Products...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 N65009 11-07-05 Rev. A 2005 Cequent Towing Products...