Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame rail
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75532F
Wrenches: 10mm, 14mm, 16mm
Drill Bits: None
Fasteners same
both sides
Hitch pushes up slightly on bottom plastic
valance panel when installed. This is how the
hitch was designed to fit. Bottom valance
panel may be removed if customer chooses.
j
Qty. (4)
Hex bolt M10X1.25X40mm CL10.9
NOTE: If present remove tow hook. Remove (2) bolts on the bottom of rail. To remove the remaining bolt lower exhaust
at the rubber isolator (2) places. Remove nuts holding the heat shield in place. Bolt is located on the inside of the
frame rail. Replace all nuts to heat shield except the one on the frame rail. Keep heat shield nut to be re-installed.
Return fasteners used for tow hook and the tow hook to owner.
1.
Detach the rubber exhaust hangers and lower the rearward portion of the exhaust (2) on each exhaust).
2.
Remove the (2) outboard nuts, one on each side, that holds the heat shield in place. Nuts to be re-installed
3.
Rotate the hitch into position over the exhaust and align the slots to the existing weld nuts. NOTE: Make sure hitch
is between the heat shield and the frame rails. Install fasteners as shown.
4.
Tighten bolts. Re-install heat shield nuts previously removed.
5.
Raise exhaust system back into position.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe sa fety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of N ew York, V.E.S.C. Regulation V-5
and SAE J684.
z
2007, 2009 Cequent Performance Products
Installation Instructions
Fascia
Hyundai Veracruz
Valance panel
pushes up slightly
Tighten all M10 CL10.9 fasteners with
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV7
Frame rail
Exhaust not
shown for clarity
Existing weld nuts
Bolt for Tow hook.
k
Qty. (4)
Conical washer
torque
wrench to 58 Lb.-Ft. (79 N*M)
Sheet 1 of 3
75532N
Part Numbers:
75532
87439
44573
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
5000 (2270 Kg)
500 (227 Kg)
5000 (2270 Kg)
500 (227 Kg)
Remove Tow
hook if present.
Weld nut
k
j
9-2-09
Rev. B
Form: F205 Rev A 5 -6-05
Publicidad
Manuales relacionados para Cequent Performance Products 75532
Resumen de contenidos para Cequent Performance Products 75532
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of N ew York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75532N 9-2-09 Rev. B 2007, 2009 Cequent Performance Products Form: F205 Rev A 5 -6-05...
- Página 2 Ce produit est conforme aux normes V -5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75532N 9-2-09 Rev. B 2007, 2009 Cequent Performance Products Form: F205 Rev A 5 -6-05...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 75532N 9-2-09 Rev. B 2007, 2009 Cequent Performance Products Form: F205 Rev A 5 -6-05...