Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Normal
bumper
fascia
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75513F
Wrenches: 15/16", 16mm-tow hook option
Drill Bits: 5/8"- Only needed to reinstall
tow hook on Patriot with optional tow hook.
Cutting Tool: Only needed to trim
bumper fascia on Compass Rallye.
Note 1.
Compass Rallye Package
It is necessary to trim bumper
fascia. Obtain vehicle owners
approval for cutting plastic fascia
before installing hitch!
See diagram.
Note 2.
Patriot with optional tow hook
On Jeep Patriot with optional tow
hook on Driver's side it is
necessary to remove tow hook.
Check with vehicle owner
to see if they want tow hook
reinstalled. To reinstall hook it is
necessary to press/drive existing
knurled neck bolts out of hook
and drill out with 5/8" drill.
Reinstall hook by using supplied
5/8" bolts following steps below.
Qty. (4)
5/8"-11 X 4-1/2" Hex Bolt
1
Qty. (2)
5/8" Lock Washer
2
1.
If vehicle has optional tow hook see Note 2. above. For Compass Rallye see Note 1. above. Check with vehicle owner.
2.
Place 5/8 hex bolts into vehicle bushings from the outboard side of the vehicle frame rails. Leave bolt ends flush with the
inboard side of frame rails.
3.
Raise hitch into position and push 5/8 hex bolts through hitch frame brackets to support the hitch.
4.
Attach remaining hardware as shown above.
5.
On Compass Rallye Package only. Use hitch receiver tube as a guide to cut a 2-1/4" wide by 2" high piece out of bumper
fascia to allow clearance for ball mounts. See diagram above.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2006, 2007, 2008, 2009 Cequent Performance Products
Installation Instructions
Jeep Compass,
Jeep Patriot,
Optional tow
hook
Rallye
Bumper
fascia
Vehicle frame
bushing typical
Optional tow hook
Reattach existing 10mm
bolt to bumper
Tighten all 5/8-11 fasteners with torque wrench to 100 Lb.-Ft. (136 N*M)
Rallye Package
inc.
optional tow hook
inc.
Do Not Exceed Lower of Towing Vehicle Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
Vehicle frame
Rail
1
3
4
1
2
4
Rear view of Rallye showing
section of fascia to trim out
Qty. (2)
5/8" Conical Washer
3
4
Qty. (4)
5/8"-11 hex Nut
Sheet 1 of 3
75513N
Part Numbers:
75513
87422
44555
75169 UHAUL
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
N/A
N/A
3500 (1 589 Kg)
350 (159 Kg)
COMPASS
Shown with hitch in place.
COMPASS
Cut up to cross hatch pattern in fascia
3-5-09
Form: F205 Rev A 5-6-05
Rev. G
Publicidad
Manuales relacionados para Cequent Performance Products 75513
Resumen de contenidos para Cequent Performance Products 75513
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2006, 2007, 2008, 2009 Cequent Performance Products Sheet 1 of 3 75513N 3-5-09 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de s écurité des systèmes d’attelage. 2006, 2007, 2008, 2009 Cequent Performance Products Feuille 2 de 3...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2006, 2007, 2008, 2009 Cequent Performance Products Sheet 3 of 3 75513N 3-5-09 Rev.