Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Vehicle Bumper
Hitch Shown In Proper Position
Equipment Required: Utility Knife
Fastener Kit: 75371F or 87403F
Wrenches: 8mm, 10mm, 18mm, 11/16", T-20
Drill Bits: ½"
C-Clamps
NOTE: Consult with owner before trimming fascia.
1.
Remove rear fascia as shown in Figure 1:
a.
On 2004 and 2005 models, remove access door from bottom of fascia and return to vehicle owner.
b.
Open tail gate, remove corner trim pieces, and remove 2 screws, 1 on each side.
c.
Remove 2 screws inside each wheel well. Pull wheel well plastic away from fascia and remove 3 more screws, each
side.
d.
Remove 1 screw and 2 plastic nuts from bottom of fascia.
e.
Carefully pull fascia straight back to remove.
2.
Trim the fascia.
a.
2004 and 2005 Models: trim inner fascia as shown in Figure 2A. Trim the inner fascia to same profile as the access
door. Trimming of the outer fascia is not required.
b.
2006 Models: trim the outer and inner fascia as shown in Figure 2B. When installing a hitch that has an electrical
bracket, use the 9-1/2" wide profile. When installing a hitch without an electrical bracket, use the 6-1/2" wide profile. In
both cases, measure about the fascia centerline as shown.
c.
On newer models more extensive inner fascia trimming required for proper fit. As shown in Figure 5.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005, 2007, 2008 Cequent Towing Products
Installation Instructions
Plastic Fascia
Access Door
FIGURE 1
BMW X3
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
2004 and 2005 Models
FIGURE 2B
2006 Models
Sheet 1 of 6
Part Numbers:
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
4,000 (1816 Kg)
3,500 (1589 Kg)
Trim Here
FIGURE 2A
Hitch With
Electrical Bracket
Hitch Without
Electrical Bracket
75371N
6-10-08
Form: F205 Rev A 5-6-05
75371
44531
87403
Max Tongue
WT (LB)
400 (182 Kg)
350 159 Kg)
Rev. D

Publicidad

loading

Resumen de contenidos para Cequent Towing Products 75371

  • Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2005, 2007, 2008 Cequent Towing Products Sheet 1 of 6 75371N 6-10-08 Rev.
  • Página 2: Installation Instructions

    This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 2 of 6 75371N 6-10-08 Rev. D 2005, 2007, 2008 Cequent Towing Products Form: F205 Rev A 5-6-05...
  • Página 3 . Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2005, 2007, 2008 Cequent Towing Products Feuille 3 de 6 75371N 6-10-08 Rév.
  • Página 4 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 4 de 6 75371N 6-10-08 Rév. D 2005, 2007, 2008 Cequent Towing Products Form: F205 Rev A 5-6-05...
  • Página 5: Números De Partes

    Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. Hoja 5 de 6 75371N 6-10-08 Rev. D 2005, 2007, 2008 Cequent Towing Products Form: F205 Rev A 5-6-05...
  • Página 6 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. Hoja 6 de 6 75371N 6-10-08 Rev. D 2005, 2007, 2008 Cequent Towing Products Form: F205 Rev A 5-6-05...

Este manual también es adecuado para:

4453187403