Descargar Imprimir esta página

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

Enlaces rápidos

ENGLISH
ENGLISH
Linking the Unit to the AV-HS6000
The following notifications are supported when the unit (V2.00-00-0.00 or later) is linked to the AV-HS6000.
⿟ Tally notifications from the switcher
⿟ Notifications for [PREVIEW] button operation triggers
Switcher connection settings are configured in the newly added [SWITCHER LINK] menu.
For details on the menu, see the following.
NOTE
⿟ The following plug-in software must be installed on the AV-HS6000 to link with it.
⿟ External_Control: For tally notifications
⿟ Macro_Trigger: For [PREVIEW] button linking
For details on configuring the plug-in software, refer to the Operating Guide for the AV-HS6000.
47 SWITCHER LINK
Press the [PREVIEW] button in the ROP panel to output a preview signal from the preview connector to the switcher.
This menu appears for cameras for which the connection setting in the [CONNECT SETTING] menu is not set to "Serial" or "LAN".
Item
SW' IP
RECEIVE UDP PORT
UPLOAD (push)
SWITCHER LINK
TALLY RECEIVE
PREVIEW
TALLY ACTION MATERIAL
TALLY ACTION CAM No.
W0321AM0 -PS
Setting value
192.168.0.5
Sets the IP address of the switcher.
65535
Sets the port number of the unit that will receive communications from the
switcher.
-
When you press the menu operation dial, the configured IP address and port
number will be applied to the unit.
OFF
Enables the link with the switcher when set to "ON".
ON
OFF
Enables reception of tally notifications when set to "ON".
ON
OFF
Sends notification of [PREVIEW] button operations to the switcher when set
ON
to "ON".
SDI_1 to SDI_32,
Selects the material.
DVI_1, DVI_2
For details, refer to the Operating Guide for the AV-HS6000.
NON,
Sets the camera number to which the tally notification will be sent for
CAM1 to CAM100
notifications of the material information configured in [TALLY ACTION
MATERIAL].
⿟ Be aware that if multiple instances of [TALLY ACTION MATERIAL] are
assigned to the same camera number, the tally indication will blink due to
the existence of lit and unlit material.
⿟ Tally control will be performed for the camera that is connected to the unit
at that moment. Tally control will not be performed for cameras that are not
connected.
AK-HRP1015G
___ indicates the factory settings.
Setting details
DVQQ1096ZA

Publicidad

loading

Resumen de contenidos para Panasonic AV-HS6000

  • Página 1 ENGLISH AK-HRP1015G Linking the Unit to the AV-HS6000 The following notifications are supported when the unit (V2.00-00-0.00 or later) is linked to the AV-HS6000. ⿟ Tally notifications from the switcher ⿟ Notifications for [PREVIEW] button operation triggers Switcher connection settings are configured in the newly added [SWITCHER LINK] menu.
  • Página 2 DEUTSCH AK-HRP1015G Verbinden des Geräts mit dem AV-HS6000 Die folgenden Benachrichtigungen werden unterstützt, wenn das Gerät (V2.00-00-0.00 oder höher) mit dem AV-HS6000 verbunden ist. ⿟ Tally-Benachrichtigungen vom Mischer ⿟ Benachrichtigungen bei Auslösen des Betriebs der [PREVIEW]-Taste Die Verbindungseinstellungen des Mischers werden im neu hinzugefügten [SWITCHER LINK]-Menü konfiguriert.
  • Página 3 FRANÇAIS AK-HRP1015G Liaison de l’appareil à l’AV-HS6000 Les notifications suivantes sont prises en charge lorsque l’appareil (V2.00-00-0.00 ou version ultérieure) est reliée à l’AV-HS6000. ⿟ Notifications de comptage de l’autocommutateur ⿟ Notifications de déclenchement de l’opération du bouton [PREVIEW] Les réglages de connexion de l’autocommutateur sont configurés dans le menu [SWITCHER LINK] nouvellement ajouté.
  • Página 4 ⿟ External_Control: per le notifiche tally ⿟ Macro_Trigger: per il collegamento al pulsante [PREVIEW] Per i dettagli sulla configurazione del software plug-in, fare riferimento alla Guida all’uso di AV-HS6000. 47 SWITCHER LINK Premere il pulsante [PREVIEW] nel pannello ROP per emettere un segnale di anteprima dal connettore di anteprima al commutatore.
  • Página 5: Enlazado De La Unidad A Av-Hs6000

    ⿟ External_Control: para las notificaciones del testigo ⿟ Macro_Trigger: para el enlazado del botón [PREVIEW] Para conocer más detalles sobre la configuración del software de visor plug-in, consulte el manual de instrucciones del AV-HS6000. 47 SWITCHER LINK Pulse el botón [PREVIEW] del panel del ROP para emitir una señal de previsualización desde el conector de previsualización al conmutador.