Using The Timer; Care And Maintenance - Russell Hobbs 25610-56 Manual De Instrucciones

KEEP WARM
• Once brewed, the hotplate will keep the coffee warm for 40 minutes after brewing. The keep warm mode is indicated by the light around the +
button coming on. After 40 minutes, the light will go out.

USING THE TIMER

Note: Make sure the clock is set to the correct time. Use the hr and min buttons.
1. Prepare the coffee maker according to which mode you are using but do not press the + button to start brewing.
2. Press the Y button. The button will flash and the Y icon will flash on the display.
Within 10 seconds of pressing the Y button, use the hr and min buttons to enter the time you want your coffee maker to start brewing.
3.
4. If a time has previously been programmed, it will flash on the display otherwise the display will show the default setting of 8:00.
5. 10 seconds after you have finished entering the time, the Y button will stop flashing and remain lit. The Y icon on the display will also stop flashing
and remain lit. Your coffee maker is now programmed to brew at the time you have entered.
• If you want to check the program time press the Y button. The programmed time will show for 3 seconds and then return to the time of day.
• If you want to cancel the timer before brewing has started, press and hold the Y button for 5 seconds until the Y light goes out and the Y icon
disappears from the display.
• If you want to stop the coffee maker while it's brewing, press the + button.
A QUICK CUP
If you want a quick cup of coffee before the brewing cycle has finished:
1. You can remove the carafe at any time. The non-drip valve will prevent coffee dripping on to the hotplate.
2. To prevent the filter holder overflowing, replace the carafe on the hotplate within about 20 seconds.
3. When you replace the carafe on the hotplate the non-drip valve opens to let any remaining coffee through.

CARE AND MAINTENANCE

GENERAL CLEANING
1. Unplug the appliance and let it cool.
2. Tip the contents of the filter holder into the bin.
3. Wipe all surfaces with a clean damp cloth.
4. Hand wash the carafe and filter holder. Wipe out the hopper with kitchen paper.
5. Wipe the shaded area shown in Fig H with a piece of damp kitchen paper. Use the brush if necessary to loosen any coffee debris.
Note: If you haven't used your coffee maker for more than 4 weeks, we recommend that you follow the steps under BEFORE USING FOR THE FIRST TIME
before brewing coffee again.
CLEANING THE GRINDER
The grinder can be disassembled in order to clean it. If you try to disassemble the grinder without first removing any surplus coffee beans, it will be very
difficult to reassemble correctly. The grinder cannot be cleaned if the coffee maker is in keep warm mode. Follow these steps:
Twist the coffee bean hopper and lid counterclockwise until the d symbol aligns with the usymbol (Fig A).
1.
2. Lift off the hopper, remove the lid and empty out any coffee beans. Wipe out the hopper with kitchen paper.
3. Replace the lid then refit the hopper onto the coffee maker aligning the d symbol with the usymbol. Twist the hopper clockwise until the d
symbol aligns with the lsymbol (Fig B).
4. Turn the grind control to the fine (l) setting.
g
5. Press the button to select the 6 cup setting.
6. Press the + button. After a few moments the grinder will start. Once it has stopped, press the + button until the +light goes out.
7. Follow step 1 again to remove the bean hopper.
Turn the grind control to the r setting (Fig C).
8.
9. Lift up the handle on the grinding head (Fig D).
10. Lift the grinding head out of the body of the appliance (Fig E). If it doesn't lift out easily, make sure that the 3 marks on the grinding head are aligned
with the b markings (Fig G).
11. Use the cleaning brush to clean the grinding head and the area where it fits into the appliance. Do not use water.
12. Refit the grinding head by aligning the 3 marks on the grinding head with the b markings and pressing it down (Fig G). Fold the handle back down.
13. Turn the grind control to any of the grind settings.
14. Refit the hopper.
SELF CLEAN
After 60 brewing cycles, the display will show CLE and the c icon to indicate that the appliance needs descaling. Descaling flushes out the deposits that
naturally build up over time.
1. Use a proprietary brand of descaler suitable for use in plastic-bodied products. Follow the instructions on the package of descaler.
Pour the descaling solution into the water reservoir to the max mark.
2.
3. Press the c button.
4. The automatic self clean process will start and will continue for about 45 minutes.
5. After the process has finished, your coffee maker will switch off.
• Products returned under guarantee with faults due to scale will be subject to a repair charge.
CLEANING FREQUENCY
Daily - Remove any used coffee grounds and filter papers as required. Clean the filter holder and carafe. Wipe the shaded area shown in Fig H with a piece
of damp kitchen paper. Use the brush if necessary to loosen any coffee debris.
Weekly - Clean the grinder.
6