Product Overview; Description Of The Product; Models And Characteristics; Preliminary Checks - Key Automation RÉVO+ REP2024 Instrucciones Y Advertencias Para Su Instalación Y Uso

EN

2 - PRODUCT OVERVIEW

2.1 - Description of the product

The RÉVO+ gear motors are destined to be installed in systems
for the automation of gates with hinged doors.
The RÉVO+ gear motors have been designed and constructed to
be fitted onto hinged doors within the weight limits indicated in the
2.2 - Model and technical characteristics
CODE DESCRIPTION
24 Vdc gear motor for single hinged door with max length 2,3 m or weight 250 Kg, 230 Vac (1 x 900PO24
REP2024
included)
24 Vdc gear motor Master for double hinged doors with max length 2,3 m or weight 250 Kg, 230 Vac (2 x
REP2024M
900PO24 included)
REP2024S 24 Vdc gear motor for hinged doors with max length 2,3 m or weight 250 Kg, 230 Vac, without control unit
REP2224 24 Vdc gear motor for hinged doors with max length 2,3 m or weight 250 Kg, 230 Vac
REP2224S 24 Vdc gear motor for hinged doors with max length 2,3 m or weight 250 Kg, 230 Vac, without control unit
TECHNICAL DATA
MODELS
TECHNICAL SPECIFICATIONS
Torque
Working cycle
Opening time at 90°
Control board
Power supply
Power supply
Absorption
Engine power
Integrated lights
Degree of protection
Dimensions (L - P - H)
Weight
Operating temperature
Leaves maximum weight

3 - PRELIMINARY CHECKS

Before installing this product, verify and check the following steps:
- Check that the gate or door are suitable for automation
- The weight and size of the gate or door must be within the
maximum permissible operating limits specified in Fig. 2
- Check the presence and strength of the security mechanical
stops of the gate or door
- Check that the mounting area of the product is not subject to
flooding
- Conditions of high acidity or salinity or proximity to heat sources
could cause malfunction of the product
- Extreme weather conditions (for example the presence of snow,
ice, high temperature range, high temperatures) may increase the
18
REP2024
Nm 120
cycles/hour 60
sec 14-20
14A
Vac 230
Vdc -
A 0,6
W 115
si
IP 44
mm
Kg 10,5
°C -20°+55°
Kg 250
technical specifications table.
The use of gear motors for applications which differ from those
indicated above is prohibited.
REP2024M REP2024S
120 120
60 60
14-20 14-20
14A -
230 -
- 24
0,6 2
115 50
si si
44 44
125 - 260 - 310
10,5 8
-20°+55° -20°+55°
250 250
friction and therefore the force required for the handling and initial
starting point may be higher than under normal conditions.
- Check that the manual operation of gate or door is smooth and
friction-free and there is no risk of derailment of the same
- Check that the gate or door are in equilibrium and stationary if
left in any position
- Check that the power line to supply the product is equipped with
proper grounding safety and protected by a magnetothermal and
differential security device
- Provide the power system with a disconnecting device with a
gap of contacts enabling full disconnection under the conditions
dictated by the overvoltage category III.
- Ensure that all materials used for the installation comply with
current regulations
REP2224 REP2224S
120 120
60 60
14-20 14-20
CT20224 -
230 -
- 24
0,6 2
115 50
- -
44 44
10,5 8
-20°+55° -20°+55°
250 250