Tabla de contenido
Manuales relacionados para Westinghouse Castle
Resumen de contenidos para Westinghouse Castle
- Página 1 ETL-ES-Castle-WH18 OWnEr'S ManuaL ManuaL dEL uSuariO Castle Please write model number here for future reference: / Por favor, incluya el número del modelo aquí para futura referencia: net Weight: 15.84 LBS Peso neto: 7.2 KGS...
-
Página 2: Safety Tips
ETL-ES-Castle-WH18 SafETy TiPS OBSErVE THE fOLLOWinG: rEad and SaVE THESE inSTruCTiOnS WarninG: TO rEduCE THE riSK Of firE, ELECTriC SHOCK, Or PErSOnaL inJury, MOunT TO OuTLET BOX MarKEd 'aCCEPTaBLE fOr fan SuPPOrT Of 35 LBS. (15.9 KG) Or LESS' and uSE MOunTinG SCrEWS PrOVidEd WiTH THE OuTLET BOX and/Or SuPPOrT dirECTLy frOM BuiLdinG STruCTurE. -
Página 3: Consejos De Seguridad
ETL-ES-Castle-WH18 COnSEJOS dE SEGuridad HaGa LO SiGuiEnTE: LEa y GuardE ESTaS inSTruCCiOnES adVErTEnCia: Para rEduCir EL riESGO dE inCEndiO, dESCarGa ELÉCTriCa O HEridaS GraVES PErSOnaLES, MOnTE En una CaJa dE EMBuTir rOTuLada “adECuada Para VEnTiLadOrES dE 35 LB (15,9 KG) O MEnOS” uTiLiZandO LOS TOrniLLOS dE MOnTaJE inCLuidOS COn La CaJa dE EMBuTir y/O MOnTE dirECTaMEnTE En La ESTruCTura dEL EdifiCiO La MayOrÍa dE LaS CaJaS dE EMBuTir uTiLiZadaS .nOrMaLMEnTE COn arTEfaCTOS dE iLuMinaCiÓn nO SOn adECuadaS Para VEnTiLadOrES y dEBErÍan SEr rEEMPLaZadaS. -
Página 4: Características
ETL-ES-Castle-WH18 fEaTurES CaraCTErÍSTiCaS SLOPED CEILING DOWNROD INSTALLATION INSTALLATION FLUSH MOUNT INSTALLATION INSTALACIóN PARA INSTALACIóN CON INSTALACIóN AL TECHO VARILLA VERTICAL TECHO INCLINADO For low ceilings For normal ceilings May require a longer downrod (sold separately) Para techos bajos Para techos normales Podría requerir una varilla vertical más larga... - Página 5 ETL-ES-Castle-WH18 fEaTurES CaraCTErÍSTiCaS COMBO-BLADE Combo-Blades feature two high quality finishes on one blade. Select the one that best complements your decor, or change the style with just a flip of the blade. NOTE: Combo-Blade finishes vary, depending upon model. ALETA DE DOBLE CARA Las aleta del rotor de doble cara presentan dos superficies con un acabado de alta calidad.
-
Página 6: Preparing For Installation Antes De La Instalación
ETL-ES-Castle-WH18 PrEParinG fOr inSTaLLaTiOn anTES dE La inSTaLaCiÓn Use metal outlet box suitable for fan support (must support 35 lbs). Before attaching fan to outlet box, ensure the outlet box is securely fastened by at least two points to a structural ceiling member (a loose box will cause the fan to wobble). -
Página 7: Mounting Bracket Installation Instalación Con Soporte De Montaje
ETL-ES-Castle-WH18 MOunTinG BraCKET inSTaLLaTiOn inSTaLaCiÓn COn SOPOrTE dE MOnTaJE Remove the screws and star washers from the two mating holes (1) on the canopy. Loosen (do not remove) the screws in the mating slots (2) on the canopy. Rotate the mounting bracket counter-clockwise and remove from the canopy. -
Página 8: Mounting Options
ETL-ES-Castle-WH18 MOunTinG BraCKET inSTaLLaTiOn MOunTinG OPTiOnS inSTaLaCiÓn COn SOPOrTE OPCiOnES dE MOnTaJE dE MOnTaJE Choose a MOunTinG OPTiOn Elija una OPCiÓn dE MOnTaJE fLuSH MOunT OPTiOn If flush mount option is selected, proceed to page 9, step 6. OPCiÓn dE inSTaLaCiÓn aL raS Si elige la opción de montaje al ras,... - Página 9 ETL-ES-Castle-WH18 fLuSH MOunT OPTiOn OPCiÓn dE inSTaLaCiÓn aL TECHO Guide motor wires through the rubber coupling cover (1) and base of the canopy (2) as shown. Slide rubber coupling cover over coupling and attach canopy directly to For flush mount option, raise fan assembly and place onto hook (1) from mount- top of motor housing with flush mount screws, and lock washers provided.
- Página 10 ETL-ES-Castle-WH18 nOrMaL dOWnrOd OPTiOn OPCiÓn COn VariLLa VErTiCaL Para TECHO nOrMaL Insert downrod into downrod coupling. Make sure to align hole in downrod with the hole in downrod coupling. Install cross pin (1) through coupling and downrod. Insert keeper pin (2) into cross pin until it snaps into place.
- Página 11 ETL-ES-Castle-WH18 EXTEndEd dOWnrOd OPTiOn OPCiÓn COn VariLLa VErTiCaL MÁS LarGa Slide downrod ball (1) off of downrod and remove pin (2). Loosen downrod ball (1) from downrod (2) by removing set screw (3). Deslice la esfera de la varilla vertical (1) hasta separarla de la Afloje la esfera de la varilla vertical (1) de la varilla vertical (2) varilla vertical y quite el pasador (2).
- Página 12 ETL-ES-Castle-WH18 EXTEndEd dOWnrOd OPTiOn OPCiÓn COn VariLLa VErTiCaL MÁS LarGa Re-install pin into extended downrod, and slide downrod ball up to the top of the downrod. Re-install set screw to secure ball to downrod. Note: Some extended downrods have a pre-drilled set-screw hole. If a pre-drilled hole is present in the extended downrod, tighten the set screw into the pre-drilled hole in the extended downrod. If no pre-drilled hole exists in the extended downrod, tighten the set screw against the downrod to secure the downrod ball.
-
Página 13: Montaje
ETL-ES-Castle-WH18 MOunTinG MOnTaJE Carefully lift fan assembly onto mounting bracket. Rotate fan until notch on downrod ball (1) engages the ridge on the mounting bracket (2). This will allow for hands free wiring. With bracket holding fan assembly, make electrical connections using the Levante con cuidado el conjunto del ventilador hasta el soporte de montaje. - Página 14 ETL-ES-Castle-WH18 WirinG OPTiOnS OPCiÓn dE CaBLEadO WaLL COnTrOL WirinG OPTiOn PuLL CHain WirinG OPTiOn *Connect blue wire only if attaching light kit with fan. *Connect blue wire only if attaching light kit with fan. Follow diagram above to make wiring connections for fan pull chain control.
- Página 15 ETL-ES-Castle-WH18 SECurE TO CEiLinG aSEGurE EL VEnTiLadOr aL TECHO For flush mount fans, carefully lift fan from the mounting bracket, making sure not to break any wire connections. For downrod fans, slide the canopy up to the mounting bracket. Para ventiladores de instalación al ras, levante con cuidado el ventilador del soporte de montaje asegurándose de que no interrumpa ninguna conexión de los cables.
-
Página 16: Blade Installation Instalación De Las Aletas
ETL-ES-Castle-WH18 BLadE inSTaLLaTiOn inSTaLaCiÓn dE LaS aLETaS Check the motor for plastic shipping stabilizer tabs (1), and remove them if they are present. Attach blade assembly to motor using the noise-dampening motor gaskets (2) and motor screws provided. Tighten screws securely. NOTE: Some models do not utilize motor gaskets, washers, or stabilizer tabs. -
Página 17: Light Fixture Installation Instalación Del Artefacto Luminoso
ETL-ES-Castle-WH18 LiGHT fiXTurE inSTaLLaTiOn inSTaLaCiÓn dEL arTEfaCTO LuMinOSO Remove one of the screws (1) on the mounting plate (3), and loosen, (do not remove) the other two (2). Quite uno de los tornillos (1) del soporte de la placa del juego de luces (3) y suelte (sin quitar) los otros dos (2). - Página 18 ETL-ES-Castle-WH18 LiGHT fiXTurE inSTaLLaTiOn inSTaLaCiÓn dEL arTEfaCTO LuMinOSO Connect the two single wire plugs form the mounting plate (1) to the two single wire plugs from the light kit plate(2). Attach the light kit plate (2) to the mounting plate (1) by placing the key slot holes from the light kit plate onto the two protruding screw heads from the mounting plate.
- Página 19 ETL-ES-Castle-WH18 LiGHT fiXTurE inSTaLLaTiOn inSTaLaCiÓn dEL arTEfaCTO LuMinOSO Install light bulbs. (included) Loosen the 3 screws from 3 protruding poles of the mounting plate. Instale las bombillas de luz. (incluidas) Afloje los 3 tornillos de los 3 postes que sobresalen de la placa de montaje.
- Página 20 ETL-ES-Castle-WH18 LiGHT fiXTurE inSTaLLaTiOn inSTaLaCiÓn dEL arTEfaCTO LuMinOSO pull chain hole glass shade hole There are total 5 holes in the decorative metal ring (1) of the glass shade. 2 of them are for pull chains going through and another 3 are for the glass shade assembly. Gently rotate the decorative metal ring (1) to ensure the 5 holes are completely aligned with the 3 protruding poles and 2 holes of the mounting plate(1).
- Página 21 ETL-ES-Castle-WH18 LiGHT fiXTurE inSTaLLaTiOn inSTaLaCiÓn dEL arTEfaCTO LuMinOSO Lead the fan pull chain and light pull chain separately through the 2 holes of the mounting plate and the 2 holes of the decorative metal ring . Install the 3 screws (removed in step 23) onto the protruding poles and tighten.
- Página 22 ETL-ES-Castle-WH18 PuLL CHainS inSTaLLaTiOn inSTaLaCiÓn dE LOS TiradOrES dE CadEnaS Assemble decorative fob and extension chains from hardware bag to fan pull chains by inserting end of chain into chain coupling. Confirm chains are held by lightly pulling both chains in coupling.
- Página 23 ETL-ES-Castle-WH18 OPEraTiOn and MainTEnanCE Operation Turn on the power and check operation of fan. The pull chain controls the fan speeds as follows: 1 pull - high; 2 pulls - medium; 3 pulls - low; 4 pulls - off. Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans and so on. The slide switch controls direction, forward or reverse.
-
Página 24: Operación Y Mantenimiento
ETL-ES-Castle-WH18 OPEraCiÓn y ManTEniMiEnTO Operación Encienda el ventilador y verifique su funcionamiento. La cadenilla de tiro controla las velocidades del ventilador de la siguiente manera: 1 jalón – rápida; 2 jalones - mediana; 3 jalones - lenta; 4 jalones - apagado. -
Página 25: Troubleshooting Guide
ETL-ES-Castle-WH18 If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some cases, these TrOuBLESHOOTinG GuidE installation errors may be mistaken for defects. If you experience any faults, please check this troubleshooting chart. If a problem cannot be remedied, please consult with your qualified electrician and do not attempt any electrical repairs yourself. - Página 26 ETL-ES-Castle-WH18 Si tiene dificultades para hacer funcionar su nuevo ventilador, podría ser a causa del armado, instalación o GuÍa Para SOLuCiOnar PrOBLEMaS cableado incorrectos. En algunos casos, estos errores de instalación podrían ser confundidos con defectos. Si experimenta alguna falla, consulte esta guía para solucionar problemas. Si no puede solucionar el problema, consulte a un electricista calificado y no intente reparar conexiones eléctricas.
- Página 27 ETL-ES-Castle-WH18...
- Página 28 ETL-ES-Castle-WH18 Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. www.westinghouselighting.com , WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation Used under license by Westinghouse Lighting All rights reserved. Made in China...