Ego Power+ RTX2300 Manual Del Operador página 8

EN WARNING:
To prevent serious personal injury,
disconnect the battery power from the tool before servicing,
cleaning, changing attachments or removing material from
the unit.
You may use this product for the purposes listed below:
Cutting:
used for cutting the grass around stakes or guard
rails, wall edges, road curbs, fences in the running traffic, or
trimming the vegetation on parking lots.
NOTICE:
When using the ROTOCUT, ensure that no foreign
objects are thrown out which entails strong risks: broken
windows, dented car bodies, slit fences, torn tree bark or
personal injury.
TO CONNECT/DISCONNECT THE BATTERY POWER
(Fig. C)
Fully charge before first use.
▲ ▲
Align of plug with
plug into the tool until the green seal completely
disappeared into the socket.
To disconnect the battery power, just unplug it by
holding and pull backward.
STARTING/STOPPING THE TOOL (FOR STX3800 &
BCX3800)
See "STARTING/STOPPING THE LINE TRIMMER/
THE BRUSH CUTTER" section in STX3800/BCX3800
operator's manual.
USING THE TOOL
WARNING:
To avoid serious personal injury, wear
goggles or safety glasses at all times when operating this unit.
Wear a face mask or dust mask in dusty locations.
Clear the area to be cut before each use. Remove
all objects, such as rocks, broken glass, nails, wire,
or line, that can be thrown or become entangled in
the cutting attachment. Clear the area of children,
bystanders, and pets. At a minimum, keep all children,
bystanders and pets at least 15m away; there still
may be risk to bystanders from thrown objects.
Bystanders should be encouraged to wear eye
protection. If you are approached, stop the motor and
cutting attachment immediately.
Before each use, check for damage/worn parts
Check the ROTOCUT head, guard and loop handle and
replace the parts that are cracked, warped, bent, or
damaged in any away.
8
ROTOCUT — RTX2300
of the machine. Insert the
WARNING: Always wear gloves when mounting
the guard or servicing the blade. Take care of the
blade and protect your hand from cutting.
After each use, clean the tool.
CAUTION: Obstructions in the vents will prevent
the air from flowing into the motor housing and result
in overheating or damaged of the motor.
◾
Use only mild soap and a damp cloth to clean the
tool. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
◾
Keep air vents in the motor housing from debris at
all times.
MAINTENANCE
WARNING: When servicing, use only identical
replacement parts. Inspect and maintain the tool
regularly. To ensure safety and reliability, all repairs
should be performed by a qualified service technician.
WARNING: Battery tools do not have to be
plugged into an electrical outlet; therefore, they are
always in operating condition. To prevent serious
personal injury, take extra precautions and care when
performing maintenance, service or for changing the
cutting attachment or other attachments.
WARNING: To prevent serious personal injury,
disconnect the battery power from the tool before
servicing, cleaning, changing add-on attachments or
removing material from the unit.
ROTOCUT BLADE REPLACEMENT
WARNING: If the blades become loose after it is
fixed in position or the blades are badly worn, replace
the blades immediately. Never use a tool with a loose
or ineffective cutting attachment.
Know the ROTOCUT head as Fig. D1 shown.
D-1 Shaft Cup D-2
D-3 Bottom-Blade D-4
D-5 Washer D-6
D-7 Nut
1. Place the gear case of the ROTOCUT head against a solid
surface. Clamp the up and down blades with pliers or in a
vise, then use the wrench to loosen the nut (Fig. D2).
2. Remove the nut, gliding bowl, washer, support cup,
down blade, up blade and shaft cup in sequence as
Fig. D1 shown.
Top-Blade
Support Cup
Gliding Bowl