Anti-Static System; Dry Vacuuming; Wet Vacuum Cleaning; Clip Connection - WOLFF M 30 Manual De Instrucciones

ATTENTION
Danger due to fine dust entering
Risk of damage to the suction motor.
Never remove the main filter element when vacuuming.
1. Connect the suction hose and attach a suction noz-
zle or connect to the dust generating device, de-
pending on the operating mode.
Intermittent tone
The horn sounds (intermittent tone) when the air speed
drops below 20 m/s.
Note
The horn reacts to a vacuum.
1. Set the turn switch to the correct hose cross-section.
Continuous tone
The horn sounds (continuous tone) when the cooling air
filter is clogged.
1. Allow the device to cool down. Clean/replace the
cooling air filter.

Anti-static system

Static charges are discharged through the earthed con-
nection nozzles. This prevents sparking and electric
shocks with electrically conducting accessories (includ-
ed in the scope of delivery).

Dry vacuuming

● The appliance is fitted with a fleece filter bag with
lock latch, order no. 163019 (5 pieces).
● The device is equipped with a dust bag with cable
ties, order no. 163020 (5 pieces).
Note
All types of dust up to dust class M can be vacuumed
with this device. The use of a dust collection bag (for or-
der no. see filter systems) is required by law.
Note
The device is suitable for industrial extraction and a dust
removal device for mobile operation for vacuuming dry,
non-inflammable dusts with workplace limit values
(AGW) greater than or equal to 0.1 mg/m
Installing the fleece filter bag
1. Unlock and remove the suction head.
2. Fit the fleece filter bag.
Illustration C
3. Fit and lock the suction head.
Installing the dust bag
Note
The dust bag opening must be pulled fully over the suc-
tion hose port.
1. Unlock and remove the suction head.
2. Fit the dust bag.
Illustration D
3. Pull the dust bag over the container.
4. Fit and lock the suction head.

Wet vacuum cleaning

DANGER
Danger from dust that is harmful to your health
Respiratory sicknesses through inhalation of dust.
No dusts harmful to health may be vacuumed when per-
forming wet vacuum cleaning.
Note
The hose filter available as an accessory with the order
number 163023 is not suitable for wet vacuum cleaning.
Horn
3
.
Installing the squeegees
1. Remove the brush strip.
Illustration E
2. Install the squeegees.
Closing the suction connection
1. Fit a plug exactly into the suction connection.
Illustration F
2. Push the plugs in until they engage.
Removing the fleece filter bag
● The fleece filter bag must always be removed when
vacuuming wet substances.
1. Unlock and remove the suction head.
2. Pull the fleece filter bag out to the rear.
Illustration G
3. Fold in the lock latch and seal the fleece filter bag
tight.
4. Dispose of the used fleece filter bag in accordance
with statutory regulations.
5. Fit and lock the suction head.
Removing the dust bag
● The dust bag must always be removed when vacu-
uming wet substances.
1. Unlock and remove the suction head.
2. Fold up the dust bag.
Illustration H
3. Pull the dust bag opening towards the rear over the
suction hose port.
4. Seal the dust bag tightly underneath the opening us-
ing cable ties.
5. Remove the dust bag.
6. Clean the container inside with a moist cloth.
7. Dispose of the dust bag in accordance with statutory
regulations.
8. Fit and lock the suction head.
● We recommend switching off the "Automatic filter
dedusting" function when vacuuming wet dirt with
the crevice nozzle or the upholstery nozzle (option-
al), or when sucking mainly water out of a container.
● The device switches off automatically when the
maximum fluid level is reached.
● When vacuuming non-conductive liquids (e.g. drill
emulsion, oils and grease) the device does not au-
tomatically switch off when the container is full. The
filling level must be continuously monitored and the
container emptied on a timely basis.
● On completion of wet vacuum cleaning: Clean the
main filter element using the filter cleaning. Clean
the electrodes with a brush. Clean the container with
a moist cloth and dry it off.
The suction hose is equipped with a clip system. All ac-
cessory parts with a nominal width of 35 mm can be
connected.
Illustration I
English
General

Clip connection

13