Husky 72WB01SS-THD Manual Del Operador
Husky 72WB01SS-THD Manual Del Operador

Husky 72WB01SS-THD Manual Del Operador

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

OPERATOR'S MANUAL
6 FT WORKBENCH
MODEL # 72WB01SS-THD
NOTE: IT IS RECOMMENDED
THAT UNIT IS ASSEMBLED WITH
AT LEAST TWO PERSONS.
SERVICE PARTS
CALL 1-866-440-3170 FOR SERVICE PARTS.
provide the Model Number when calling. To expand your garage
storage project, please visit www.homedepot.com/garagestorage
for additional product options.
Locating Model # Information
Model numbers and other information required for service parts is
located on a white label on the upper right hand corner of the unit.
CAPACITIES
• Weight of the unit is 94 lbs.
• The maximum load capacity for the work surface is 1000 lbs.
evenly distributed.
• The maximum product weight, including contents stored on the
work surface is 1094 lbs.
MAINTENANCE
PAINTED SURFACES:
• Periodically the surfaces should be cleaned with a mild
detergent and water.
• Grease and oil can be removed with most standard cleaning
fluids. For safety, use a nonflammable cleaning fluid.
• Auto wax will preserve the unit's luster finish. Apply the wax
as to a car. The wax will also help protect the unit against
scratches.
STAINLESS SURFACES:
• Stainless steel can discolor when exposed to pool chemi-
cals, saltwater or cleaners with bleach.
• Keep your stainless looking new by cleaning with a good
quality all-in-one stainless steel cleaner polish monthly.
Frequent cleaning will remove surface contamination that
could lead to rust.
• Do not clean with steel wool or other abrasive pads.
• Do not use cleaners not specifically intended for
stainless steel on stainless surfaces (this includes
glass, tile and counter cleaners).
DANGER
situation which, if not avoided, will result in serious injury
or death.
WARNING
if not avoided, could result in serious injury or death.
CAUTION
which, if not avoided, may result in minor injury, moderate
injury, or property damage.
CAUTION:
Operating Instructions before first use of this product.
DANGER
DO NOT
Please
cause personal injury.
DO NOT
other moving object. This may cause personal injury or
product Damage.
APPROPRIATELY SECURE
moving it with a forklift.
WARNING
USE APPROPRIATE SAFETY
using power and hand tools. Failure to do so may cause
personal injury or product damage.
USE ADEQUATE MANPOWER
and moving this unit. Failure to do so may cause personal
injury or product damage.
DO NOT
cause product damage or personal injury.
UNIT MUST BE
product may become unstable and tip if stored or moved
on an un-level surface, which may cause personal injury
or product damage.
SAFETY
is used to indicate a hazardous
indicates a hazardous situation which,
is used to indicate a hazardous situation
Read and follow all Safety Rules and
stand on this product. You may fall which may
mount this product on a truck bed or any
this product before
equipment when
alter this product in any manner. This may
located on a level surface. The
when assembling
F1831

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Husky 72WB01SS-THD

  • Página 1 Frequent cleaning will remove surface contamination that 6 FT WORKBENCH could lead to rust. MODEL # 72WB01SS-THD • Do not clean with steel wool or other abrasive pads. • Do not use cleaners not specifically intended for stainless steel on stainless surfaces (this includes glass, tile and counter cleaners).
  • Página 2: Carton Contents

    HARDWARE CARTON CONTENTS TOOLS REQUIRED: A. Side Socket Wrench 3/8in Socket Extension B. Rail - Top Back 7/16in Deep-well Socket 3/8in Wrench C. Workbench Top Drill 1/8in Drill bit D. Rail - Top Front Square Tape measure E. Bottom Rail OPTIONAL TOOLS: Screwdriver, Flathead and 7/16-in Open End Wrench HARDWARE INCLUDED:...
  • Página 3 • Place Workbench Top, with stainless steel side facing GG - Leveling Foot, Right (Qty: 2) down. (Use packaging material to prevent scratches.) NOTE: The Rail with the Husky® nameplate should be Process: placed toward the front of the unit with the nameplate •...
  • Página 4 BOTTOM RAIL ASSEMBLY Items Needed: E - Bottom Rail (Qty: 1) AA - 1/4-20 x 5/8in Carriage Bolt (Qty: 4) BB - 5/16in Washer (Qty: 4) CC - 1/4-20 Flange Nut (Qty: 4) Process: • Attach rail E in top back set of holes in both sides A as shown, using (4) bolts AA, (4) washers BB, and (4) nuts 1-1/2 inches Mounting Holes...
  • Página 5: Superficies Pintadas

    • La grasa y el aceite pueden retirarse con la mayoría de los líquidos BANCO DE TRABAJO DE 1.8 M (6 FT) estándar para limpieza. Por razones de seguridad, utilice un líquido MODELO 72WB01SS-THD incombustible para limpieza. • Si se suministran forros para las gavetas, se recomienda que se utilicen para proteger el acabado interno de las mismas y para facilitar la limp- ieza.
  • Página 6: Contenido De La Caja

    HERRAMIENTAS CONTENIDO DE LA CAJA HERRAMIENTAS NECESARIAS: A. Lado Llave de cubo Extensión de cubo de 7.6 cm (3in) B. Riel – Fondo Superior Cubo profundo de 11.1 mm (7/16in) C. Superficie del Banco de Trabajo Llave de 8.7 mm (3/8in) Taladro D.
  • Página 7: Montaje De Los Lados

    • Coloca (1) almohadilla de la pata niveladora (FF) y la otra NOTA: El Riel con la chapa Husky® debe colocarse hacia el almohadilla de la pata niveladora (GG) en cada lado del fondo. frente de la unidad con la chapa invertida.
  • Página 8: Quitar Película Protectora De Acero Inoxidable

    Elementos necesarios: E - Riel (cantidad: 1) AA - Perno con cabeza de hongo de 1,6 cm (5/8in) de largo, 6,4 mm (1/4in) de diámetro y 20 roscas por pulgada (cantidad: 4) BB - Arandela de 7,9 mm (cantidad: 4) CC - Tuerca de la brida dentada de 6,4 mm (1/4in) de diámetro y 20 roscas por pulgada (cantidad: 4) Proceso:...

Tabla de contenido