Troubleshooting - Performance Tool W10011 Manual Del Propietário

TROUBLESHOOTING

INSUFFICIENT AIR FLOW:
Probable Cause
Loss of air pressure
Tank fills slowly
Tank won't hold enough air
Air leakage
Gauge won't register/
/registers incorrectly
Tank won't accept air
Chuck pin floating
or "crooked"
Safety pressure bypass
valve seeps air
PERFORMANCE TOOL® extends only the following warranties, and only to original retail purchasers. These warranties give specific legal
rights. Except where prohibited by local law, the law of the State of Washington governs all warranties and all exclusions and limitations of
warranties and remedies. There may be other rights which vary from state to state.
PERFORMANCE TOOL® warrants the product to be free from defects in materials and workmanship under normal use and service. A
defective product may be returned for a free replacement within 90 days from the date of purchase, provided that product is returned to
place of purchase immediately after discovery of defect. After 90 days and up to one year from date of purchase, PERFORMANCE TOOL®
will replace at no charge any parts which our examination shall disclose to be defective and under warranty. These warranties shall be
valid only when a sales receipt showing the date of purchase accompanies the defective product or defective part(s) being returned. For
part(s) after 90 days, please remit your request, postage prepaid to:
These warranties exclude blades, bits, punches, dies, bulbs, fuses, hoses, and other consumables which must be replaced under normal
use and service. These warranties shall not apply to any product or part which is used for a purpose for which it is not designed, or which
has been repaired or altered in any way so as to affect adversely its
performance or reliability, nor shall these warranties apply to any product or part which has been subject to misuse, neglect, accident or
wear and tear incident to normal use and service.
PERFORMANCE TOOL® does not authorize any other person to make any warranty or to assume any liability in connection with its
products.
Except for warranties of title and the limited express warranties set forth above, PERFORMANCE TOOL® makes no express or implied
warranties of any kind with respect to its products. In particular, PERFORMANCE TOOL® makes no implied warranty of merchantability
and no implied warranty of fitness for any particular purpose, except that for goods purchased primarily for personal, family or household
use and not for commercial or business use, PERFORMANCE TOOL® makes an implied warranty of merchantability (and, if otherwise
applicable, an implied warranty of fitness for a particular purpose), but only for the particular qualities or characteristics, and for the
duration, expressly warranted above.
The laws on limitation of implied warranties may differ from state to state, so the above limitations may not apply in all cases.
PERFORMANCE TOOL® shall not be liable for consequential, incidental or special damages resulting from or in any manner related to any
product, or to the design, use, or any inability to use the product. The sole and exclusive remedy for a defective product or part shall be the
repair, or replacement thereof as provided above. The laws on limitation of remedies or on consequential, incidental or special damages
may vary from state to state, so the above limitations may not apply in all cases.
LIMITED WARRANTY
PERFORMANCE TOOL, P.O. Box 88259 Tukwila, WA 98138
© Copyright 2013 WILMAR CORPORATION, P.O. Box 88259 Tukwila, WA 98138
Solution
Possible leak. Locate by applying soap &
water mixture to seams, fittings, etc.
Check opening for obstructions.
Clean or replace as necessary or check
your air source, make sure it is 125 PSI.
Check air pressure at fill stem with a tire
gauge. Replace pressure gauge if it does
not agree. Or check your air source, make
sure it is 85-125 PSI.
Use teflon/thread tape on fittings, hoses
and gauge. Check tank for dirty, worn or
damaged parts. Replace as necessary.
Be sure that the needle is moving freely by
tapping the gauge.
Fill stem pin may be bent. Replace air manifold.
Turn On/Off air adjustment dial to the ON position.
If pin is lodged, tap back of chuck on a hard
surface.
Pull ring twice to seat with pressure in tank.