ETI 64102161 Manual De Uso Y Cuidado

UsE anD CarE GUiDE
inTEGral DriVEr BallasT ByPass TUBE
Package contents
Part Description Quantity
A LED Tube 1
B C-Clip 1
C Screw 1
A
96˝
nOTE: Keep your receipt and these instructions for proof of purchase
WarninG: Shut off the power at the circuit breaker or fuse panel before removing the old fixture, ballast, or
fluorescent tubes.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.
InstaLLatIon
1. Shut off power at the electrical panel before beginning the installation.
2. Remove existing fluorescent tubes and set aside to recycle in accordance with local requirements.
3. Remove and set aside the ballast cover, if needed.
4. Use the existing shunted sockets if they in good condition. If not, it is recommended that new shunted sockets (not
included) are installed.
nOTE: C-Clip should be installed in the fixture to prevent lamp radiation and provide extra security for high
vibration areas.
retrofIt LuMInaIre WIth 1 LaMP
Electronic
Ballast
Fluorescent lamp
Lampholder
retrofIt LuMInaIre WIth 2 LaMPs
Electronic
Ballast
Fluorescent lamp
Lampholder
Fluorescent lamp
Lampholder
retrofIt LuMInaIre MagnetIc baLLast
Magnetic
Ballast
Fluorescent lamp
Lampholder
care anD cLeanIng
Ordering # 64102161
Part # T8BP-8-55-850-MV-DE
CaUTiOn: Before attempting to clean the tube and luminaire/light fixture, disconnect the power to the fixture by
Certification # 64102161
turning the breaker off or removing the fuse from the fuse box. Clean with a soft, dry cloth. Do not use cleaners with
chemicals, solvents, or harsh abrasives. Do not use liquid cleaner on the LEDs, LED driver, or wiring.
troubLeshootIng
Minor problems often can be fixed without the help of an electrician.
WarninG: Before doing any work on the fixture, disconnect power to the light fixture.
Problem
The fixture will not light.
C
B
The fuse blows or the
1˝
circuit breaker trips when
the light is turned on.
WarninG: Carefully read and understand the information given in this manual before beginning the assembly
and installation. Failure to do so so could lead to electric shock, fire, or other injuries which could be hazardous
or even fatal. • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn
off the circuit breaker. • This product must be installed in accordance with the applicable installation codes by a
person familiar with the construction and operation of the product and the hazards involved. • Risk of electrical
shock. To reduce the possibility of serious injury, always take the proper precautions and unplug the fixture before
moving or cleaning. • Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires
electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician. • Risk of fire or
electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in
the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of
the luminaire. • Do not make or alter any open holes in an enclosure of wiring or electrical components during kit
installation. • To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp
objects.
CaUTiOn: Not for emergency lighting.
WarninG: THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF
THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION. • Installers should not
disconnect existing wires from lampholder terminals to make new connections at lampholder terminals. Instead
installers should cut existing lampholder leads away from the lampholder and make new electrical connections to
lampholder lead wires by employing applicable connectors. • THERE ARE LED TUBE, OPERATION INSTRUCTION AND
FIELD APPLIED LABEL IN THIS RETROFIT KIT.
The units covered by this report were intended to be retrofit surface mounted with a diffuser for this model number. Type
IC and non-IC recessed mounted fluorescent luminaires use a maximum of two lamps, the minimum lamp compartment
dimensions are below:
Model
number
641021XX
nOTiCE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the
equipment into an outlet on a circuit different from that to which the receiver is connected, and consult the dealer or an
experienced radio/TV. Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
WarrantY
This product is warranted for a period of 5 years from the date of original purchase against defects in materials and
workmanship. If this product should fail to operate due to defects in material or workmanship within 60 months of
purchase, see www.ETiSSL.com for details. This product will be repaired or replaced, at ETi's option. This warranty is
expressly limited to repair or replacement of product and liability for direct, incidental, or consequential damages is
hereby expressly excluded. Some states do not allow exclusions of direct, incidental or consequential damages, so
the above limitation of exclusion may not apply to you. This warranty gives the consumer specific legal rights, which
vary from state to state. WARRANTY IS VOID IF PRODUCT IS NOT USED FOR THE PURPOSE WHICH THIS PRODUCT IS
MANUFACTURED.
Possible cause solution
The power is off. Ensure the power supply is on.
The circuit breaker is off. Ensure the circuit breaker is in the on position.
There is a bad connection. Check to ensure proper wire connections are made. Contact
a qualified electrician.
There is a defective switch. Contact a qualified electrician.
The LED tubes are installed Install LED tubes with the end labeled "power this end" to
incorrectly. the wired sockets.
The wires are crossed or the Check the wire connections. Contact a qualified electrician
power wire is grounding out. or call customer service 1-855-384-7754.
Minimum Lamp compartment Dimensions Maximum Lamp
[Length x Width x height] [in] Quantity
96 x 1 x 1 2
Questions, problems, missing parts?
Call ETiSSL Customer Service
8 a.m. - 5 p.m., CST, Monday - Friday
1-855-etI-ssLI (1-855-384-7754)
www.etissL.com
GUiDE D'UTilisaTiOn ET D'EnTrETiEn
TUBE PassE-BallasT aVEC TransFO inTÉGrÉ
contenu De L'eMbaLLage
Pièce Désignation Quantité
A Tube DEL 1
B Pince en C 1
C Vis 1
96˝
rEMarQUE : Gardez votre facture ainsi que ces instructions comme preuves d'achat.
aVErTissEMEnT : Coupez le courant au panneau de disjoncteurs ou de fusibles avant d'enlever le vieux
luminaire, le ballast ou les tubes fluorescents.
Si vous n'êtes pas familiers avec les installations électriques, nous vous recommandons de faire ppel à un électricien
qualifié pour l'installation.
InstaLLatIon
1. Coupez le courant au panneau électrique avant de faire l'installation.
2. Enlevez les tubes fluorescents existants et mettez-les de côté aux fins de recyclage conformément aux règlements
locaux.
3. Au besoin, enlevez le couvre-ballast et mettez-le de côté.
4. Utilisez les douilles shuntées actuelles si elles sont en bon état. Autrement, on recommande l'installation de douilles
neuves (non fournies).
rEMarQUE : La pince en cé devrait être installée sur le luminaire afin d'empêcher le rayonnement de la lampe
et plus de sécurité aux endroits où il y a de fortes vibrations.
MoDIfIer un LuMInaIre À un tube
Ballast
électronique
Tube fluorescent
Douilles
MoDIfIer un LuMInaIre À DeuX tubes
Ballast
électronique
Tube fluorescent
Douilles
Fluorescent lamp
Douilles
MoDIfIer un LuMInaIre aVec baLLast MagnÉtIQue
Ballast
magnétique
Tube fluorescent
Douilles
n° de commande 64102161
n° de pièce T8BP-8-55-850-MV-DE
n° de certification 64102161
C
B
A
1˝