Westin 27-1635 Instrucciones De Montaje

MOUNT KIT
EQUIPO DE MONTAJE
JEU DE MONTAGE
27-1635
CONTENTS -
ITEM QTY
1 2 STEP BOARD (PURCHASED SEPARATELY)
2 6 MOUNT BRACKET
3 12 M8 SQUARE HEAD BOLT
4 12 M8 FLAT WASHER
5 12 M8 LOCK NUT
6 12 M8-1.25 FLANGE NUT
1 2 ESTRIBOS (SE COMPRAN POR SEPARADO)
2 6 PIEZAS DE SUJECIÓN
3 12 PERNOS CON CABEZA CUADRADA DE M8
4 12 ARANDELAS PLANAS DE M8
5 12 TUERCA PRESIÓN DE M8
6 12 TUERCA A PRESIÓN CON BRIDA DE M8-1,25
1 2 MARCHEPIED (VENDU SÉPARÉMENT)
2 6 SUPPORTS
3 12 BOULON A TETE CARREE M8
4 12 RONDELLES PLATES M8
5 12 ECROU A FREIN M8
6 12 ECROU FREINE A EMBASE DE M8-1,25
STEP 1. Remove contents from box and check for damage. Verify all parts are present. Read instructions completely before
beginning. It is strongly recommended to install the Sure Grip Gap Strip for these vehicle applications.
STEP 2. Attach mounting brackets as shown. SEE FIGURE 1.
STEP 3. Insert square head bolts as shown (3 per slot, 6 per board). SEE FIGURES 3 AND 4. NOTE: For lighted boards, run wiring
harness prior to attaching board to brackets (Refer to Step 4). SEE FIGURES 3 AND 4. Run longer wire harness on
passenger side.
STEP 4. For Sure-Grip Running Boards, slide closure strip as shown. Set lights (if purchased) in appropriate location. Attach to
Sure-Grip Running Board as shown. SEE FIGURE 2. Drill hole through plastic strip and run wires as shown. SEE FIGURE
5.
STEP 5. Attach board to brackets as shown. Make sure board and brackets are properly aligned and tighten fasteners.
Recommended torque values are 23 FT.LBS. for 8mm fasteners. SEE FIGURE 6.
NOTE: For lighted version of Molded Step Board, remove plastic cover from each end of under side of board. Proceed
to
Steps 6-7.
WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN RECOMMENDS
USING A PROFESSIONAL FOR THIS INSTALLATION. NOTE: AVOID AREAS OF EXCESSIVE HEAT, VIBRATION, PINCH OR
ROTATION WHEN SECURING HARNESS TO VEHICLE. CAUTION: ALWAYS USE A FUSED(+) POSITIVE SUPPLY SOURCE.
HINT: Molded Step Boards: For longevity, check rubber seals before installation. Rubber grommets around red and
blue wires going into rear sockets, should be inserted and recessed about 1/4". NOTE: Remove bulbs and apply white
grease into sockets and replace bulbs. Apply RTV Silicone where lights go into socket. Install lights and run wire loom
as shown. SEE FIGURE 4. For Sure-Grip Running Boards, run wire loom down center as shown. SEE FIGURE 3.
STEP 6. Determine whether your vehicle has a positive or negative switching courtesy system or an auxiliary light source (most
Fords). Obtain an accurate wiring diagram for your vehicle's courtesy light system.
For positive and negative switching:
Locate a pass-through point (usually under carpet at driver side door sill) for the wire harness. Locate main courtesy
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2005-18 NISSAN FRONTIER KING CAB/CREW CAB; 2005-12
PATHFINDER
APLICACIÓN: 2005-18
2005-12
APPLICATION: 2005-18 NISSAN FRONTIER KING CAB/CREW CAB; 2005-12 PATHFINDER
CONTENIDO - CONTENU
UNDERCOAT SEAL FOR HARSH WEATHER.
NISSAN FRONTIER KING CAB/CREW CAB; PATHFINDER, MOD.
2
TOOLS-
ECO: W18-0111
HERRAMIENTA -OUTILS
13MM SOCKET
13MM WRENCH
RATCHET
TORQUE WRENCH
DADO DE 13MM
LLAVE DE TUERCAS DE 13MM
MANERAL
LLAVE DE TORQUE
DOUILLE 13MM
CLEF 13MM
CLIQUET
ClÉ DE COUPLE
75-0731 REVISION D 09/05/18