Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

AUTOMOTIVE PRODUCTS, INC.
MOUNT KIT
EQUIPO DE MONTAJE
27-6600 / 27-6100 / 27-6105
JEU DE MONTAGE
27-1625
SURE-GRIP
OPTIONAL LIGHT
KIT
27-6000
ITEM
QTY
CONTENTS -
1,2
2
STEP BOARD, PASSENGER (1) AND DRIVER (2) (SOLD SEPARATELY)
3,4
2
FRONT BRACKET, PASSENGER (3) AND DRIVER (4)
5,6
2
REAR BRACKET, PASSENGER (5) AND DRIVER (6)
7
8
M8-1.25 X 25MM HEX HEAD BOLT
8
8
5/16-18 X .75" SQUARE HEAD BOLT
9
16
5/16" FLAT WASHER
10
8
5/16-18 LOCK WASHER
11
8
5/16-18 LOCK NUT
1,2
2
ESTRIBOS, ACOMPAÑANTE (1) CONDUCTOR (2) (SE COMPRA SEPARADO)
3,4
2
SOPORTE DELANTERAS, ACOMPAÑANTE (3) Y CONDUCTOR (4)
5,6
2
SOPORTE CENTRAL / TRASERAS, ACOMPAÑANTE (5) Y CONDUCTOR (6)
7
8
PERNOS CON CABEZA HEXAGONAL DE M8-1,25 X 25MM
8
8
PERNOS CON CABEZA CUADRADA DE 5/16-18 X ,75
9
16
ARANDELAS PLANAS DE 3/8"
10
8
ARANDELAS DE PRESIÓN DE 3/8"
11
8
TUERCA PRESIÓN DE 5/16-18
1,2
2
MARCHE-PIEDS, PASSAGER (1) ET CONDUCTEUR (2) (ACHETE SEPAREMENT)
3,4
2
SUPPORTS AVANT, PASSAGER (3) ET CONDUCTEUR (4)
5,6
2
SUPPORTS CENTERAL / ARRIERE, PASSAGER (5) ET CONDUCTEUR (6)
7
8
BOULONS A TETE HEXAGONALE M8-1,25 X 25MM
8
8
BOULON A TETE CARREE 5/16-18 X ,75 PO
9
16
RONDELLES PLATES 5/16 PO
10
8
RONDELLES A FREIN 5/16 PO
11
8
ECROU A FREIN 5/16-18
STEP 1.
Remove contents from box and check for damage. Verify all parts are present. Read and understand instructions before beginning. NOTE: Westin
does not recommend using closure strip for this application.
STEP 2.
Attach mounting brackets as shown. See Figures 1 and 2.
STEP 3.
Insert square head bolts as shown (2 per slot, 4 per board). See Figures 4 and 5. NOTE: For lighted boards, run wiring harness prior to attaching board
to brackets (Refer to Step 6). See Figures 4, 5 & 8). Run longer wire harness on passenger side.
STEP 4.
For Sure-Grip Running Boards: Set lights (if purchased) in appropriate location. Attach to Sure-Grip Running Board as shown. Attach to running board
as shown. See Figure 3. Drill hole through plastic strip and run wires as shown. See Figure 6.
STEP 5.
Attach board to brackets as shown. Make sure board and brackets are properly aligned and tighten fasteners. Recommended torque values are 10
FT.LBS. for 5/16" square head fasteners and 16 FT.LBS. for M8 fasteners. SEE FIGURE 7. NOTE RUNNING BOARD MAY BE TRIMMED DOWN 6 INCHES
TO PROPERLY ALLIGN WITH THE CAB OF THE VEHICLE.
WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN RECOMMENDS USING A PROFESSIONAL FOR THIS
INSTALLATION. NOTE: AVOID AREAS OF EXCESSIVE HEAT, VIBRATION, PINCH OR ROTATION WHEN SECURING HARNESS TO VEHICLE. CAUTION:
For Sure-Grip Running Boards, run wire loom down center as shown. SEE FIGURE 5.
STEP 6.
Determine whether your vehicle has a positive or negative switching courtesy system or an auxiliary light source (most Fords). Obtain an accurate
wiring diagram for your vehicle's courtesy light system.
For positive and negative switching:
Locate a pass-through point (usually under carpet at driver side door sill) for the wire harness. Locate main courtesy wire (usually wire lead to dome
light). NOTE: If you do not use the main courtesy wire, lights will only function when one door is open. Route wire harness so that the 2 female
connections (from step board) are nearest to pass thru point.*Connect opposite step board lead to either connection. Connect the splicing lead to
remaining female socket and route one wire thru pass thru point. SEE FIGURE 8.
VERY IMPORTANT - Double check that your system has positive or negative switching.
For positive switching only: Connect positive wire to main courtesy system, (usually wire lead to dome light). TEST CONTINUITY BEFORE CONNECTING
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION:
APLICACIÓN:
APPLICATION:
RUNNING BOARDS
CONTENIDO
- CONTENU
ALWAYS USE A FUSED(+) POSITIVE SUPPLY SOURCE. UNDERCOAT SEAL FOR HARSH WEATHER.
2005-12 TOYOTA TACOMA REGULAR CAB
2005-12 TOYOTA TACOMA CABINA REGULAR
2005-12 TOYOTA TACOMA CABINE ET RÉGULIER
1
2
ECO W11-0124
3
5
4
TOOLS-
HERRAMIENTA
-OUTILS
7/16" SOCKET
7/16" WRENCH
13MM SOCKET
13MM WRENCH
RATCHET
TORQUE WRENCH
DADO DE 7/16"
LLAVE DE TUERCAS DE 7/16"
DADO DE 13MM
LLAVE DE TUERCAS DE 13MM
MANERAL
LLAVE DE TORQUE
DOUILLE 7/16 PO
CLEF 7/16 PO
DOUILLE 13MM
CLEF 13MM
CLIQUET
CLÉ DE COUPLE
75-0109 REVISION A 1-16-12
6

Publicidad

loading

Resumen de contenidos para Westin 27-1625

  • Página 1 RONDELLES A FREIN 5/16 PO ECROU A FREIN 5/16-18 STEP 1. Remove contents from box and check for damage. Verify all parts are present. Read and understand instructions before beginning. NOTE: Westin does not recommend using closure strip for this application. STEP 2.
  • Página 2 FINISH PROTECTION Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax, (e.g. Pure Carnauba) on a regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and open it PASO 1.
  • Página 3 PROTECTION DE LA FINISSION Les produits Westin ont une finission de haute qualité qui requiert des soins, comme toute autre finission du véhicule exposée aux éléments. Protégez la finission à l’aide d’une cire non-abrasive (par exemple, Pure Carnauba) de façon régulière. L’usage de tout savon, pâte à polir ou cire contenant un abrasif est nuisible, puisque Thank You for choosing Westin products Westin Automotive Products, Inc.
  • Página 4 FORWAR D DELANT ERA FORWAR D AVANT DELANT ERA AVANT REAR PASSENGER SHOWN FRONT PASSENGER SHOWN FIGURE 1 FIGURE 2 LADO DEL ACOMPAÑANTE TRASERAS LADO DEL ACOMPAÑANTE DELANTERAS FIGURA 1 FIGURA 2 PASSAGER ARRIERE PASSAGER AVANT FIGURE 3 FIGURA 3 FIGURE 4 FIGURE 5 FIGURA 4...

Este manual también es adecuado para:

27-600027-660027-610027-6105