Westin 27-1655 Instrucciones

AUTOMOTIVE PRODUCTS, INC.
MOUNT KIT
EQUIPO DE MONTAJE OPTIONAL LIGHT
JEU DE MONTAGE
27-1655
SURE-GRIP
BOARDS
27-6150
27-6155
27-6550
ITEM QTY CONTENTS -
1 2 STEP BOARD (PURCHASED SEPARATELY)
2,3 4 FRONT/CENTER BRACKET, PASSENGER (2) AND DRIVER (3)
4,5 2 REAR BRACKET, PASSENGER (4) AND DRIVER (5)
6 2 FRONT SUPPORT BRACE
7 2 REAR SUPPORT BRACE
8 2 SPACER TUBE (CENTER BRACKET ONLY)
9 4 M12 X 120MM HEX HEAD BOLT
10 2 M12 X 130MM HEX HEAD BOLT
11 4 3/8-16 X 1.25" HEX HEAD BOLT
12 8 3/8" FLAT WASHER
13 4 3/8" LOCK WASHER
14 4 3/8-16 HEX NUT
15 4 1/4-20 X 1.0" SELF DRILLING BOLT
16 12 5/16-18 X .75 SQUARE HEAD BOLT
17 12 5/16" FLAT WASHER
18 12 5/16" LOCK NUT
19 6 1/2" FLAT WASHER
20 6 1/2" LOCK WASHER
1 2 ESTRIBOS (SE COMPRAN POR SEPARADO)
2,3 4 PIEZAS DE SUJECIÓN DELANTERO/CENTRAL , LADO DEL ACOMPAÑANTE (2) Y EL CONDUCTOR (3)
4,5 2 PIEZAS DE SUJECIÓN TRASERAS , LADO DEL ACOMPAÑANTE (4) Y EL CONDUCTOR (5)
6 2 PIEZA DE SUJECIÓN DEL SOPORTE DELANTERO
7 2 PIEZA DE SUJECIÓN DEL SOPORTE TRASERAS
8 2 TUBO SEPARADOR (SOPORTES CENTRAL SOLAMENTE)
9 4 PERNOS CON CABEZA HEXAGONAL
10 2 PERNOS CON CABEZA HEXAGONAL DE M12 x 130mm
11 4 PERNOS CON CABEZA HEXAGONAL DE 3/8 -16 x 1,25"
12 8 ARANDELAS PLANAS DE 3/8"
13 4 ARANDELAS DE PRESIÓN DE 3/8"
14 4 TUERCAS HEXAGONALES DE 3/8 - 16
15 4 PERNOS AUTOPERFORANTES DE 1/4 - 20 x 1,0"
16 12 PERNOS CON CABEZA CUADRADA DE 5/16"
17 12 ARANDELAS PLANAS DE 5/16"
18 12 TUERCA A PRESIÓN DE 5/16"
19 6 ARANDELAS PLANAS DE 1/2"
20 6 TUERCA A PRESIÓN DE 1/2"
1 2 MARCHEPIED (VENDU SÉPARÉMENT)
2,3 4 SUPPORTS AVANT/CENTRAL, PASSAGER (2) ET CONDUCTEUR (3)
4,5 2 SUPPORTS ARRIERE, PASSAGER (4) ET CONDUCTEUR (4)
6 2 RENFORTS POUR SUPPORTS AVANT
7 2 RENFORTS POUR SUPPORTS ARRIERE
8 2 TUBE D'ESPACEMENT
` 9 4 BOULONS A TETE HEXAGONALE DE M12 X 120MM
10 2 BOULONS A TETE HEXAGONALE DE M12 X 130MM
11 4 BOULON A TETE HEXAGONALE DE 3/8 -16 X 1,25 PO
12 8 RONDELLE PLATE DE 3/8 PO
13 4 RONDELLE A FREIN DE 3/8 PO
14 4 ECROU HEXAGONAL 3/8 -16
15 4 BOULON AUTOPERCEUR DE 1/4 - 20 X 1PO
16 12 BOULON A TETE CARREE 5/16-18 X .75
17 12 RONDELLE PLATE DE 5/16 PO
18 12
ECROU A FREIN 5/16-18
19 12 RONDELLE PLATE DE 5/16 PO
20 12 ECROU A FREIN 5/16-18
STEP 1. Remove contents from box and check for damage. Verify all parts are present. Read and understand instructions before beginning. It is strongly recom-
mended to install the Sure Grip Gap Strip for these vehicle applications.
STEP 2. Attach mounting brackets as shown.
STEP 3. Insert square head bolts as shown (3 per slot, 6 per board).
board to brackets (refer to Step 6)
STEP 4. For Sure-Grip Running Boards, slide closure strip as shown. Set lights (if purchased) in appropriate location. Attach to Sure-Grip Running Board as shown.
SEE FIGURE 8. Drill hole through plastic strip and run wires as shown.
Attach board to brackets as shown. Make sure board and brackets are properly aligned and tighten fasteners. Recommended torque values are 26 FT. LBS.
STEP 5.
for 3/8" fasteners, 23 FT.LBS. for 8mm fasteners, 10 FT.LBS. for 5/16" square head fasteners and 7 FT. LBS. for 1/4" fasteners. S
NOTE: For lighted version of Molded Step Board, remove plastic cover from each end of under side of board. Proceed to Steps 6-7.
WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN RECOMMENDS USING A
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2005-08 DODGE DAKOTA QUAD CAB
APPLICACIÓN: DODGE DAKOTA QUAD CAB MOD. 2005-08
APPLICATION: 2005-08 DODGE DAKOTA QUAD CAB
SURE-GRIP
KIT
27-6000
1
CONTENIDO - CONTENU
(CENTER BRACKET ONLY)
DE M12 x 120mm
(CENTRAL SUPPORT SEULEMENT)
SEE FIGURES 1, 2, 3 AND 4.
SEE FIGURES 5, 6 AND 10.
.
(SOPORTES CENTRO SOLAMENTE)
(CENTRE SUPPORT SEULEMENT)
SEE FIGURES 5 AND 6. NOTE:
Run longer wire harness on passenger side.
SEE FIGURE 9.
WO:
2 3
5
4
TOOLS-HERRAMIENTA-OUTILS
3/4" SOCKET
9/16" SOCKET
18MM SOCKET
9/16" WRENCH
DRILL MOTOR
RATCHET
SOCKET DRIVER
TORQUE WRENCH
DADO DE 3/4"
DADO DE 9/16"
DADO DE 18MM
LLAVE DE TUERCAS DE 9/16"
TALADRO ELÉCTRICO
LLAVE DE DADO
LLAVE DE TORQUE
MANERAL
DOUILLE 3/4 PO
DOUILLE 9/16 PO
DOUILLE 18MM
CLE 9/16 PO
PERCEUSE ELECTRIQUE
CLE A CANON
CLIQUET
CLE DE COUPLE
For lighted boards, run wiring harness prior to attaching
75-0732 REVISION B 6/30/08
6
8
7
EE FIGURE 6.