Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Hitch fits under factory hitch
Frame rail
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: F75132
Wrenches: 7/8", 15mm, 18mm
Drill Bits: None
Frame rail
Qty.
M12 X 1.75 X 45mm, CL10.9 Hex Bolt
1
(6)
Qty.
1/2" Conical Washer
2
(8)
Qty.
1/2" – 13 X 1.75 GR5 Carriage Bolt
3
(2)
1.
Remove (3) existing bumper bracket nuts if present, and (3) M12 or M14 bolts from each side of frame.
2.
Fishwire carriage bolts and blocks through end of frame.
3.
Raise hitch into position and loosely install conical washers and nuts.
4.
Vehicles with 14mm factory fasteners: Reinstall factory M14 fasteners.
Vehicles with 12mm factory fasteners: install and torque supplied M12 fasteners and reinstall factory M12 nuts.
Note! Do not use both hitches at the same time. This may overload and cause damage to vehicle.
Tighten all M14 fasteners with torque wrench to 148 Lb.-Ft., 201 N*M
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
© 2006, 2014 Cequent Towing Products – Printed in Mexico
Installation Instructions
Ford Explorer - 4 door
Mercury Mountaineer
Lincoln Aviator
Factory hitch
Existing weldnuts-typical
Factory hitch bracket
Tighten all 1/2" fasteners with torque wrench to 75 Lb.-Ft., 102 N*M
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
3
4
2
5
Typical both sides
Qty.
1/4" X 1-1/2" X 2" Block
4
(2)
Qty.
1/2" – 13 Hex Nut
5
(2)
Tighten all M12 fasteners with torque wrench to 92 Lb.-Ft., 125 N*M
N75132
Part Numbers:
75132
44722
87417
Max Gross
Max Tongue
Trailer Weight
Weight
8000 lb, 3632 kg
800 lb, 363 kg
5000 lb, 2724 kg
500 lb, 272 kg
1
2
For vehicles with 14mm factory
bolts - Reinstall 14mm bolts.
Typical both sides
05-13-14
Rev. C
Form: F205 Rev A 5-6-05

Publicidad

loading

Resumen de contenidos para Cequent Towing Products 75132

  • Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. © 2006, 2014 Cequent Towing Products – Printed in Mexico Sheet 1 of 3...
  • Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. © 2006, 2014 Cequent Towing Products - Imprimé au Mexique Feuille 2 de 3...
  • Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2006, 2014 Cequent Towing Products - Impreso en México Hoja 3de 3...

Este manual también es adecuado para:

4472287417