JB Systems DJ-KONTROL 3 Manual De Instrucciones página 5

ENGLISH
CONFIGURING VIRTUALDJ
Setting up the DJ-KONTROL3 in VirtualDJ LE is very simple: simply follow the same setup as shown below:
The master output is sent to the rear speaker outputs and the PFL-signal (headphones) is sent to the front
speaker outputs of the internal soundcard.
ASIO-drivers:
If you absolutely want to have extremely low latency (delay), you can also experiment with ASIO-drivers if
you like: in that case you can select "ASIO-
driver" for the soundcard. Since this is out of
the scope of this manual, we will not explain
the configuration of the ASIO-drivers here.
USING OTHER DJ-SOFTWARE
Since this controller is designed as a MIDI-compatible device, you can use it to control any Midi DJ-software.
Of course this means that you will need special MIDI-mapping files for these products. Please check our
website (www.jbsystems.be): we will provide MIDI-mapping files for some other DJ-software free of charge.
VIRTUALDJ TUTORIALS
In the next chapter we give you a brief overview of the functions in VirtualDJ LE that comes with your
controller. VirtualDJ is a very intuitive program so you will easily learn it while trying all possibilities. If you
want to learn more, please check the VirtualDJ website for video tutorials and extra user guides:
www.virtualdj.com/wiki/index.html .
JB SYSTEMS
®
USER MANUAL
5/54 DJ-KONTROL 3
ENGLISH
FUNCTIONS (MIXER)
1. TRACK SELECT knob: turn this knob to scroll up or down in
the folders, browser or music library.
 Press shortly: to select the folder or file.
 Press for 0,5sec: to enlarge/shrink (zoom) the browser.
2. LOAD A button: press this button to load the selected track
to player A (left side) of the software.
3. LOAD B button: press this button to load the selected track
to player B (right side) of the software.
4. BACK button: this button allows you to return to a higher
level in the folder/browser structure.
5. GAIN knob: turn this knob to adjust the gain of the
corresponding channel.
6. HIGH knob: used to adjust the high frequencies of the
corresponding channel. Press the knob to toggle the KILL-
function on/off.
7. MIDDLE knob: used to adjust the middle frequencies of the
corresponding channel. Press the knob to toggle the KILL-
function on/off.
8. LOW knob: used to adjust the low frequencies of the
corresponding channel. Press the knob to toggle the KILL-
function on/off.
9. CHANNEL FADER: adjusts the volume of the corresponding
audio channel.
10. MIC VOLUME: used to adjust the sensitivity of the DJ-
microphone.
11. MIC INPUT: 6.3mm input jack to connect your DJ
microphone.
12. CROSSFADER: with this fader you can mix over between
both channels. The crossfader only works when you move
the channel faders (9) of both channels to the desired level!
13. CROSSFADER CURVE: used to choose a soft or hard curve
for the crossover. This depends on your personal taste.
14. CUE MIX: With this knob you can mix the input channels to the headphone output:
 Put the knob in the extreme left position to hear the PFL signals of the players.
 Put the knob in the extreme right position to hear the mixed master output signal.
 Put the knob in any other position to hear a mix of the two signals.
This option makes it possible to check your mix before you put it on the master output.
15. CUE VOLUME knob: used to control the output level of the headphone channel.
16. PHONES OUTPUT: connect your headphones here for monitoring of your tracks.
17. CUE SELECT button left: press this button to monitor player1 while the channel fader is closed.
18. CUE SELECT button right: press this button to monitor player2 while the channel fader is closed.
19. MASTER VOL knob: used to set the volume of the master output.
FUNCTIONS (PLAYERS)
20. SET CUE button: sets the track at the desired location. It also sets the audio to the last set cue
position. Keep the button pressed to preview the cue point until the button is released.
21. CUE PLAY button: starts playing the track from the last set cue position.
22. PLAY PAUSE button: used to start/stop playback of the loaded track.
23. JOG WHEEL: its function depends on the selected play mode:
 In pause mode: the wheel allows you to set a cue point or starting point very precisely.
 In play mode: the wheel acts as pitch bend.
JB SYSTEMS
®
USER MANUAL
6/54 DJ-KONTROL 3