Cequent Performance Products 60952 Instrucciones De Instalación

Equipment Required:
Fastener Kit: KA-8002-153
Wrenches: Ratchet, 3/4" socket, 3/4" wrench
Tie down hook
Frame
Carriage Bolt 1/2" x 1-1/2"
1 1 1 1 Qty. (2)
Reinforcement Plate 1/4 X 1 X 3
2 2 2 2 Qty. (2)
Conical Washer 1/2"
3 3 3 3 Qty. (3)
Hex Nut 1/2"
4 4 4 4 Qty. (3)
INSTRUCTIONS:
1. Lower exhaust by removing both rubber isolators from muffler hangers. Be careful not to allow muffler to fall under its own weight.
2. Thread bolt leader onto end of carriage bolt (1) and insert bolt leader through reinforcing plate (2). Insert carriage bolt (1) head first through
mounting hole, followed by reinforcing plate (2) in driver's side of frame. Check to see if reinforcing plate and bolt head will fit through access
hole, if not modify hole to accept hardware. (Enlarge hole just enough to get hardware through). Carefully pull down back through SAME
hole in frame until bolt and plate assembly is in position. Repeat for other side of vehicle.
3. Install 2-1/2" carriage bolt (5) through square hole spacer (6) and vehicle's tie down loop from the right hand side. Slip round hole spacers (7)
onto bolt and then through hitch's mounting tab as shown in illustration. Note: Hitch should be mounted to left side of tie down loop with spacers
(7) between it and loop. Install hex nut and hand tighten to hold hitch in place.
4. Fish bolt leaders through holes in hitch's frame straps and being careful not to push bolt assemblies back into frame channels, raise hitch's frame
straps up to vehicle's frame, remove bolt leaders and install conical washers and hex nuts (4). Make sure rubber breather hose on charcoal
canister at driver's side is
not kinked or pinched, hose should sit freely below frame strap.
5. Bend the exhaust hanger pins to lower exhaust 1/2". Raise exhaust back into position and reinstall rubber isolators.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z 2002, 2005, 2006, 2015 Cequent Performance Products - Printed in Mexico
Installation Instructions
Honda CR-V
(Sold separately)
Drawbar Kit:
3593
Drawbar must be used in the
Rise position only.
5
6
7
3
4
Tighten all 1/2" GR5 fasteners with torque wrench to 72 Lb.-Ft. (98 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
1
Wiring Access Location: SUV3
2
3
4
Carriage Bolt 1/2" x 2-1/2"
5 5 5 5 Qty. (1)
Spacer 1/4 X 1 X 2 (square hole)
6 6 6 6 Qty. (1)
Spacer 1/4 X 1 X 2 (round hole)
7 7 7 7 Qty. (2)
Sheet 1 of 3
Part Numbers:
60952
24772
77149
60952N 10-13-15
Form F206 Rev A 5605
Rev. C