Cequent Performance Products 24887 Instrucciones De Instalación

Frame rail
Rearward
Fascia
Hitch Shown In Proper Position
Equipment Required: Pull wire,
Galvanic isolators (provided),
lubricant or soapy water, tin snips,
Fastener Kit: 24887F
Wrenches: M10, 11/16, & 3/4
Drill Bits: ¼"
Rearward
Muffler
Tail pipe
.750
.375
Frame
rail
1.000
Figure 2
Access hole modification to allow
for block and carriage bolt.
j
Qty. (1) Carriage bolt ½-13 X 2.00 GR5
k
Spacer ¼" x 1.50 x 3.00
Qty. (1)
l
Conical washer ½"
Qty. (1)
m
Qty. (1) Hex nut ½-13
n
Qty. (1) Carriage bolt 7/16-14 X 1.75 GR5
Note: sort hardware prior to hitch installation to confirm 1/2" & 7/16" conical washer are kept with coordinated 1/2" & 7/16" bolts and bolt lengths are installed in
proper locations.
1. Lower exhaust at the rubber isolator. Spraying a lubricant or soapy water on the metal hanger rod and the rubber isolator helps removal.
2. Remove rearward m6 bolt holding heat shield in place. Return to owner. Trim heat shield for access to hole on passenger frame rail. Fig 4
3. Remove the rubber plug from the hole on the driver side frame rail.
4. Enlarge holes on both frame rails as shown Fig 2. Note: scrape undercoating and caulking from bottom of frame rails large enough to allow the hitch brackets
to sit flush against the frame rails.
5. Install 7/16 carriage bolts using the reverse pull wire procedure as seen in Fig 3. Leave pull wires attached. Note: length of bolts. Item 5 driver side, Item 10
passenger side.
6. Install the ½ carriage bolt and spacer as shown in Fig 1. to the tie down hook.
7. Apply the clear galvanic isolators to the passenger side bracket as shown. Fig 1
8. Feed the pull wires through the slots on the hitch brackets.
9. Raise the hitch into position and install 1/2 carriage bolt to the vehicles tie down hook, do not tighten down at this point. Fig 1.
10. Feed the 7/16 fasteners through slots on both sides remove pullwires and install fasteners as shown Fig 1. Note: on passenger side sandwich the heat shield
between the frame rail and the hitch.
11. Center the hitch on the vehicle.
12. Torque all fasteners to specifications shown below.
13. Reinstall exhaust.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and
exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut
access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
© 2012, 2015, 2016 Cequent Performance Products, Inc – Printed in Mexico
Installation Instructions
NISSAN VERSA SEDAN
Drawbar must be used in the
RISE position only.
Trim heat shield as shown.
Access hole under heat
shield passenger side only
Frame
rail
Rubber
isolator
Figure 4
Trim heat shield as
*
p
shown.
q
*Drivers side only
Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
(Sold separately)
Drawbar Kit:
3592
A. Insert bolt and
n
o
j
k
l
r
m
o
Qty. (2)
p
Qty. (1)
q
Qty. (2)
r
Qty. (2)
s
Qty. (1)
Sheet 1 of 3
Part Numbers:
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: SUV3, 4
B. Align block on
access hole
Block into frame
Figure 3
Pull wire Procedure
Note: orientation
of spacer
Tie down hook
Exhaust & heat
Figure 1
shield not shown
Spacer 1/8" X .90 X 3.00
Spacer ¼" X 1.50 X 2.00
Conical washer 7/16
Hex nuts 7/16-14
Carriage bolt 7/16-14 X 1.50 GR5
24887N 05-27-16
Form: F205 Rev A 5-6-05
24887
60304
77275
C. Pull bolt thru
block
s
o
Galvanic
isolators
between
heat shield
and hitch
q
bracket
r
Rev. C