Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
LC-BMRC-01
BMW / Mini Chime Retention
2006-2015
• Provides accessory power (12-volt 10-amp)
• Retains R.A.P. (retained accessory power)
• Provides NAV outputs (parking brake, reverse, and V.S.S)
• Retains warning chimes
• For non-amplified models, or when bypassing a factory amplifier
• Retains balance and fade
• Micro "B" USB updatable
INTERFACE COMPONENTS
• LC-BMRC-01 interface • LC-BMRC-01 harness
• Fuse holder with 96" length of wire
BMW
1 Series (without amp)
2008-2013
3 Series (without amp)
2006-2013
M3 (without amp)
2007-2013
axxessinterfaces.com
Axxess Integrate
Installation instructions for part LC-BMRC-01
FEATURES
APPLICATIONS
MINI
Cooper (without amp)
TABLE OF CONTENTS
Connections to be made ................................................... 2
Installing the LC-BMRC-01 ............................................... 3
Initializing the LC-BMRC-01 ............................................. 3
TOOLS REQUIRED
• Wire cutter • Crimp tool • Solder gun • Tape
• Connectors (example: butt-connectors, bell caps, etc.)
CAUTION!
2007-2015
especially air bag indicator lights must be connected before cycling
the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
•
metraonline.com
All accessories, switches, climate controls panels, and
© COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
Publicidad
Tabla de contenido
Manuales relacionados para Axxess LC-BMRC-01
Resumen de contenidos para Axxess LC-BMRC-01
- Página 1 • Connectors (example: butt-connectors, bell caps, etc.) • For non-amplified models, or when bypassing a factory amplifier • Retains balance and fade • Micro “B” USB updatable INTERFACE COMPONENTS • LC-BMRC-01 interface • LC-BMRC-01 harness • Fuse holder with 96” length of wire APPLICATIONS MINI CAUTION!
-
Página 2: Connections To Be Made
LC-BMRC-01 Connections to be made From the LC-BMRC-01 harness to the aftermarket radio: The following (3) wires are only for multimedia/navigation radios that require these wires. • Connect the Black wire to the ground wire. • Connect the Blue/Pink wire to the VSS/speed sense wire. - Página 3 Attention! If the interface loses power for any reason, the following steps will need to be performed again. Also, if installing an ASWC-1 connect it after you initialize • Connect the LC-BMRC-01 harness into the interface, and then to the vehicle. and test the interface/radio, with the key in the off position.
-
Página 4: Important
Installation instructions for part LC-BMRC-01 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. -
Página 5: Características
Instrucciones de instalación para la pieza LC-BMRC-01 LC-BMRC-01 INDICE BMW / Mini Retención de Timbre Conexiones que se deben hacer ........2 2006-2015 Instalación del LC-BMRC-01 ..........3 Inicialización del LC-BMRC-01 ........3 CARACTERÍSTICAS • Provee corriente de accesorios (12 voltios 10 amperes) •... -
Página 6: Conexiones Que Se Deben Hacer
LC-BMRC-01 Conexiones que se deben hacer From the LC-BMRC-01 harness to the aftermarket radio: Los siguientes (3) cables son para radios de mercado secundario con multimedios/ navegación que tienen estos cables. • Conecte el cable negro al cable de tierra. -
Página 7: Instalación Del Lc-Bmrc
Además, si la instalación de un ASWC-1 conectarlo • Conecte el arnés LC-BMRC-01 a la interfase, y después al vehículo. después de inicializar y probar la interfaz / radio, con la llave en la posición de •... -
Página 8: Importante
Instrucciones de instalación para la pieza LC-BMRC-01 IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente...