Descargar Imprimir esta página
Axxess AX-MITSUCAM-6V Instrucciones De Instalación
Axxess AX-MITSUCAM-6V Instrucciones De Instalación

Axxess AX-MITSUCAM-6V Instrucciones De Instalación

Publicidad

Enlaces rápidos

Installation Instructions for AX-MITSUCAM-6V
AX-MITSUCAM-6V
Mitsubishi Backup Camera Retain/Add-On
2014-up
INTERFACE FEATURES
• Retains the factory backup camera to an aftermarket radio
• Allows an aftermarket camera to be added to the factory screen
• Includes the AX-CAM6V 12-volt to 6-volt converter
INTERFACE COMPONENTS
• AX-MITSUCAM-6V harness • AX-CAM6V 12-volt to 6-volt converter
APPLICATIONS
MITSUBISHI
Lancer
Lancer Sportback
Outlander
Outlander Sport
TOOLS REQUIRED
• Wire cutter • Crimping tool • Solder gun • Tape
• Connectors (example: butt connectors, bell caps, etc.)
CAUTION!
All accessories, switches, climate controls panels, and especially air bag indicator lights
must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
®
axxessinterfaces.com • metraonline.com
Axxess Integrate
REV. 9/27/16
© COPYRIGHT 2016 METRA ELECTRONICS CORPORATION
2014-up
2014-up
2014-up
2014-up
Installation Instructions for AX-MITSUCAM-6V
Connections to be made
The AX-MITSUCAM-6V can be connected two different ways
To retain the factory backup camera to an aftermarket radio:
• Connect the Black wire to chassis ground, and also to the Black wire of the AX-CAM6V.
• Connect the Yellow wire to battery power.
• Connect the Red wire to the Blue/Red wire of the AX-CAM6V.
• Connect the Green/Purple wire to the reverse wire of the aftermarket radio,
and also to the Blue/White wire of the AX-CAM6V.
• Connect the male Yellow RCA jack to the rear camera input of the aftermarket radio.
To allow an aftermarket camera to be added to the OEM screen:
• Connect the Black wire to the ground wire of the aftermarket camera.
• Connect the Yellow wire to battery wire of the aftermarket camera.
• Connect the female Yellow RCA jack to the aftermarket camera.
• The AX-CAM6V 12-volt to 6-volt converter will not be used in this application.
K
P
NOWLEDGE IS
OWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
axxessinterfaces.com • metraonline.com
Axxess Integrate
REV. 9/27/16
© COPYRIGHT 2016 METRA ELECTRONICS CORPORATION
Metra recommends MECP
certified technicians

Publicidad

loading

Resumen de contenidos para Axxess AX-MITSUCAM-6V

  • Página 1 INTERFACE COMPONENTS To allow an aftermarket camera to be added to the OEM screen: • AX-MITSUCAM-6V harness • AX-CAM6V 12-volt to 6-volt converter • Connect the Black wire to the ground wire of the aftermarket camera. • Connect the Yellow wire to battery wire of the aftermarket camera.
  • Página 2 • Conecte el conector RCA macho amarillo RCA en la entrada de la cámara COMPONENTES DE LA INTERFASE de reversa del radio de mercado secundario. • Arnés AX-MITSUCAM-6V • AX-CAM6V 12 voltios al convertidor de 6 voltios Para permitir que se añada una cámara de mercado secundario a la pantalla de equipo original: APLICACIONES •...