Maintenance Notes; Disposal Information - Modellsport Multiplex HIMAX C 2212-0840 Instrucciones

Measure the current drain of your motor under load at full-
throttle. Both excessive rotational speed and overloading can
result in the motor overheating. The maximum period of 15
seconds for full-load running should only be used for 3-D
manoeuvres, which should be spaced out to leave plenty of time
for the power system to cool down again at low load.
2. M
AINTENANCE NOTES
Brushless motors are almost completely maintenance-free,
although a little care will make them last longer. Protect the
motor - and especially the ballraces - from dust and dirt, as
soiled bearings may jam completely. For this reason we
recommend that you lubricate the bearings regularly with low-
viscosity (thin) oil. Do not submerge the motor in water or
solvent. Do not kink the motor cables, and do not subject them
to vibration. Be sure to balance your propellers carefully to guard
against vibration and to avoid premature bearing damage.
3. T
IPS FOR POWER SYSTEM DESIGN
The design of the power system must reflect the model type, the
type of flying envisaged, and the model aircraft's all-up weight. If
hand-launched, models require a minimum of around 80 Watts
per kg of take-off weight, while for ground take-off the figure
should be at least 110 Watts. You can calculate the required
power based on the model's all-up weight and its flying
capability. Take 90% of the nominal battery voltage as the basis
for your calculation; this means 1.1 Volts for one NC or NiMH
cell, and 3.3 Volts for one LiPo cell. You can find the required
current by dividing the desired Wattage by the Voltage. You can
then read off the required propeller size from the graphs.
4. P
ROPELLER SELECTION
Start with the information in the graphs. We recommend that you
try out various propellers in order to find the optimum
combination.
Always keep within the maximum permissible motor speed.
Note that a 3-D model requires an entirely different propeller
from a model which is to fly very fast. In general terms, 3-D
models require a diameter : pitch (D:P) ratio of up to 0.5 (around
10 x 5" or 12 x 5"). Faster models need a D:P ratio between 0.6
and 0.8. Model aircraft designed for high-speed flying require
propellers with a D:P ratio of 1.0, such as 10 x 10" or 13 x 13".
Maximum static thrust is obtained with a D:P ratio of 0.5,
whereas maximum speed comes with a ratio of 1.0. When
making these calculations always observe the maximum
permissible rotational speed of the motor and propeller.
MULTIPLEX Modellsport GmbH & Co. KG • Neuer Weg 2 • D-75223 Niefern-Öschelbronn • www.multiplex-rc.de
Himax HC2212
Brushless out-runner motor
5. G
MULTIPLEX products are covered by the statutory guarantee
regulations relating to manufacturing and material defects, as
well as damage which arises under normal conditions, i.e. when
the item is used according to the instructions.
The guarantee does not cover damage caused by incorrect
handling, modifications to the motor, excessive current and
excessive voltage, damage caused by model crashes, or
overheating due to excessive propeller size or motor speed. We
do not accept liability for damage consequent upon the use of
the motor.
If you have queries, ideas, or wish to return your Himax motor
for repair or for any other reason, please contact us at the
address below:
6. CE
The products described in these instructions satisfy all the
statutory relevant EG directives. These are the EMV directives
89/336/EWG, 91/263/EWG and 92/31/EWG.
The controllers have been tested according to the following
basic norms:
You are therefore the owner of a product whose design fulfils the
protective aims of the European Community relating to the safe
operation of equipment.
7.
Electrical equipment marked with the cancelled waste bin
symbol must not be discarded in the standard household waste;
instead it must be taken to a suitable specialist disposal system.
In the countries of the EU (European Union)
electrical equipment must not be discarded via the
normal domestic refuse system (WEEE - Waste of
Electrical and Electronic Equipment, directive
2002/96/EG). You can take unwanted equipment to
your nearest local authority waste collection point or
recycling centre. There the equipment will be
disposed of correctly and at no cost to you.
By returning your unwanted equipment you can make an
important contribution to the protection of the environment.
2/2
UARANTEE
MULTIPLEX Customer Service Dept.
Neuer Weg 15
D-75223 Niefern
Germany
e-mail: service@multiplexrc.de
Tel.: 0049-7233-7333
APPROVAL
Interference emission:
Interference rejection:
and
D
ISPOSAL INFORMATION
EN 50 081-1:1992
EN 50 082-1:1992
EN 50 082-2:1995
Page