Descargar Imprimir esta página
Glacier bay HWH24D Guía De Uso Y Cuidado

Glacier bay HWH24D Guía De Uso Y Cuidado

Tocadores de vanidad

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

TOOLS REQUIRED
Claw hammer
Safety goggles
Measuring tape
Wall hardware
Installation
1
PREPARING FOR INSTALLATION
NOTE: Before installation, make
sure all parts are present. Compare
parts with the Hardware Included list.
If any part is missing or damaged, do
not attempt to install the product.
□ Determine the desired mounting location,
and mark the wall where the unit will be
installed.
NOTE: For secure installation, the
unit must be mounted to at least one
wall stud.
4
INSTALLING THE CABINET
□ For wall stud installation, insert #12 x 3 in. screws with
washers into the stud locations (not included).
□ For drywall installation, drill holes at the appropriate
locations and insert toggle bolts with washers (not included).
□ For concrete wall installation, drill 1/4 in. holes at the
appropriate locations and insert #12 wall anchors, followed
by #12 x 3 in. screws (not included).
5
INSTALLING THE HARDWARE
□ Attach the knobs (AA) to the door on the vanity with
short screws (BB) and to the drawers on the vanity with
long screws (CC).
Phillips
screwdriver
Power drill
Caulk/sealant
Keyhole saw
2
CUTTING THE OPENING FOR
PLUMBING FIXTURES
NOTE: This step applies to vanity
cabinets with full back panels only.
□ Locate and mark plumbing on the back panel.
□ Drill a pilot hole through the back panel.
□ Use a keyhole saw to cut an opening for the
plumbing fixtures.
Use and Care Guide
HARDWARE INCLUDED
AA - Knob
24"
x 3
30"
x 3
36"
x 3
48"
x 5
60"
x 6
Level
BB
AA
Please contact 1-888-774-8062 for further assistance.
Item #1000 723 562
Item #1000 877 517
Item #1000 877 550
Item #1000 877 616
Item #1000 877 682
Item #1000 722 014
Item #1000 722 588
Item #1000 285 504
Item #1000 285 570
Item #1000 285 603
Model #HWH24D
Model #HWH30D
Model #HWH36D
Model #HWH48D
Model #HWH60D
Model #HNHK30D
Model #HNHK36D
Model #HOA30D
Model #HOA36D
Model #HOA48D
Vanity Combo
BB - Short
CC - Long
Screw
Screw
x 1
x 2
x 1
x 2
x 1
x 2
x 1
x 4
x 2
x 4
3
POSITIONING THE
CABINET
□ Move the cabinet into
place, and use wood
shims to level the
cabinet against the wall.
CC
HOMEDEPOT.COM

Publicidad

loading

Resumen de contenidos para Glacier bay HWH24D

  • Página 1 Item #1000 877 616 Item #1000 877 682 Item #1000 722 014 Item #1000 722 588 Item #1000 285 504 Item #1000 285 570 Item #1000 285 603 Model #HWH24D Model #HWH30D Model #HWH36D Model #HWH48D Model #HWH60D Model #HNHK30D Model #HNHK36D...
  • Página 2 Installation (continued) REMOVING THE DRAWER □ Press release levers in opposite directions while pulling drawer out of the vanity. Press Press upward downward RE-INSTALLING THE DRAWER NOTE: Drawer should install smoothly; however, there may be minor resistance when the drawer is approximately half to two-thirds installed. This is normal. □...
  • Página 3 Núm. de artículo1000 723 562 Núm. de artículo1000 877 517 Núm. de artículo1000 877 550 Núm. de artículo1000 877 616 Núm. de artículo1000 877 682 Núm. de artículo1000 722 014 Núm. de artículo1000 722 588 Núm. de artículo1000 285 504 Núm.
  • Página 4 Instalación (continuado) EXTRACCIÓN DEL CAJÓN □ Presiona las palancas de desbloqueo en direcciones opuestas mientras sacas el cajón del gabinete. Presiona Presiona hacia arriba hacia abajo INSTALACIÓN DEL CAJÓN NOTA: El cajón debe instalarse suavemente aunque puede existir una pequeña resistencia cuando la instalación haya llegado aproximadamente a la mitad o a los dos tercios.

Este manual también es adecuado para:

Hwh30dHwh36dHwh48dHwh60dHnhk30dHnhk36d ... Mostrar todo