Cleaning And Care - Wahl X-Block Operación Manual

DESCRIPTION OF PARTS (FIGURE 1)
A. Blade set
B. On/off switch
C. Hanging ring
D. Cord
E. Transformer
F. Plug
G. Blade release button
H. Blade latch
I. Blade retainer
J. Drive Tip
K. Drive Tip Removal Tool
L. Cleaning brush
M. Blade oil
DIRECTIONS:
• This clipper is equipped with two different operating speeds. Turn the clipper on by sliding the on/off switch upward. The first click up from the "off" position
is the first speed and runs at 3,700 strokes per minute (SPM). The second click up from the "off" position is the second speed and runs at 4,500 strokes
per minute (SPM). After use, switch the clipper off by sliding the on/off switch all the way back down.

CLEANING AND CARE

• Do not immerse the clipper in water!
• After each use, use the cleaning brush to remove loose hair from the clipper housing and the blade set.
• The blade set should be oiled frequently (daily) in order to maintain its good cutting performance and thus ensuring a long service life. Only use Wahl
Clipper Blade Oil. Wahl Clipper blade oil has been specifically formulated for Wahl Clipper blades. Using any other lubricant may cause damage to
your blades and clipper and would void your clipper's warranty.
• Properly oil your blade using the 5 Point Oiling Method (Figure 2). Place 3 drops of oil along the top of the blade teeth at the left corner, right corner,
and center of the blade. Turn the clipper to its side and place a drop of oil at the heel of the top blade. Repeat on the other side. Let the clipper run for
30 seconds to allow the oil to work its way into the blade set.
• Wipe away any excess oil. Only wipe the clipper with a soft cloth, which may be dampened slightly. Do not use solvents or abrasives! (Figure 3)
• The blade set may be cleaned with Wahl Clipper Clini-Clip hygienic spray. Do not use any other cleaning agent. Wahl Clipper Clini-Clip has been
specifically formulated for Wahl Clipper blades. Using any other cleaning agent may cause damage to your blades and clipper and would void your
clipper's warranty.
• Insufficient maintenance of the blade set can reduce the operating time considerably.
• Care should be used to keep the cord untwisted and undamaged. When storing the clipper, coil the cord. Wrapping the cord around the clipper for
storage can cause strain to the cord, which over time, can lead to the loosening of the wires and/or electrical shortages.
CHANGING THE BLADE SET
• Switch off the clipper using the on/off switch.
• Locate the blade release button on the backside of the clipper. Press in the blade release button and gently pull the blade away from the clipper. Slide the
blade off the blade latch (Figure 4).
• To place a new blade on the clipper, ensure that the blade latch is in the correct, upright position, not lying flat against the clipper.
• If the blade latch is not upright, you will need a flathead screwdriver to pry it up. (Figure 5). Use the flathead screwdriver to pry open the blade latch from
the side. Do not attempt to pry the blade latch open from the top as there is a chance the drive tip could be damaged.
• Insert the blade onto the blade latch (Figure 6) by sliding the blade retainer over the blade latch. Before snapping the blade into place, turn the clipper
back on. It is important the clipper be running as this ensures the blade will seat properly. Use the palm of your hand to guide the blade to the clipper
There will be an audible "click" when the blade is set in place.
CHANGING THE DRIVE TIP
• Switch off the clipper using the on/off switch.
• Remove the blade (see instructions above).
• Using the drive tip removal tool, gently pull the drive tip off the blade drive.
• Using the drive tip removal tool, gently push the new drive tip onto the blade drive.
• Reattach the blade.
LIMITED 2 (TWO) YEAR WARRANTY
If your Wahl Product fails to operate satisfactorily within two years from the date of original purchase or receipt as a gift, Wahl will at our option repair or
replace it and return it to you FREE OF CHARGE. Our warranty does not cover blades, brushes, or other wear out parts. Please contact Wahl Clipper
Corporation's Service and Repair Center located in Sterling, IL at 1-800-PRO-WAHL to receive pre-paid mailing instructions.
Products out of warranty will be repaired at our standard repair charges. This warranty is void and no repair or replacement will be made under this
warranty or otherwise if:
1. The product is modified in any manner.
2. The product is repaired by anyone other than Wahl Clipper Corporation or a Wahl Clipper Corporation Authorized Service Center.
3. The product has been subject to unreasonable use.