Grounding Information; Warranty - Oreck XL ORBITER RORB400 Serie Manual Del Usuario

CAUTION
This appliance must be connected to a grounded
metal, permanent wiring system; or an
equipment-grounding conductor must be run with
the circuit conductors and connected to the
equipment-grounding terminal or lead on the
appliance.
ALWAYS UNPLUG THE MACHINE BEFORE
INSTALLING OR REMOVING ACCESSORIES.
ALWAYS WEAR SHOES WHEN USING
ELECTRICAL EQUIPMENT.
SAVE THESE INSTRUCTIONS

Grounding Information

L CAUTION L
This appliance must be grounded. If it should malfunction
or break down, grounding provides a path of least
resistance for electrical current to reduce the risk of electric
shock. This appliance is equipped with a cord having an
equipment-grounding conductor and grounding plug. The
plug must be inserted into an appropriate outlet that is
properly installed and grounded in accordance with all
local codes and ordinances.
L WARNING L
Improper connection of the equipment-grounding conductor
can result in a risk of electric shock. Check with a qualified
electrician or service person if you are in doubt as to
whether the outlet is properly grounded. Do not modify the
plug provided with the appliance - if it will not fit the outlet,
have a proper outlet installed by a qualified electrician.
This appliance is for use on a nominal 120-volt
circuit, and has a grounded plug that looks like the plug
illustrated in Sketch A (see next column). A temporary
adapter that looks like the adapter illustrated in Sketch B
(see next column) may be used to connect this plug to a
2-pole receptacle, if a properly grounded outlet is not
available. The temporary adapter should be used only until
a properly grounded outlet can be installed by a qualified
electrician. The green colored rigid ear, lug, or the like
extending from the adapter must be connected to a
permanent ground such as a properly grounded outlet box
cover. Whenever the adapter is used, it must be held in
place by a metal screw.
NOTE: In Canada, the use of a temporary adapter is not
permitted by the Canadian Electrical Code.
E N G L I

Warranty

Oreck Corporation (Oreck) gives you the following
limited warranty for this product only if it was originally
purchased for use, not resale, from Oreck or an ORECK
AUTHORIZED Dealer.
Oreck will repair or replace, free of charge, to the original
purchaser, any part, which is found to be defective in
material or workmanship within one (1) year of the date
of purchase for all models. Note: The 550 series Floor
Machine is intended for commercial use. Any commercial
use voids of the 400, 600 or 700 series voids the
warranty.
Components returned prepaid to an Oreck Factory
Authorized Service Center or to Oreck will be repaired or
replaced free of cost at the option of Oreck and/or its
service center when upon examination by either of them,
such components are found to be defective.
Brushes, pads, drive blocks and other parts are subject to
normal wear and are not covered by this limited warranty.
This limited warranty does not apply to any part subjected
to accident, abuse, alteration, misuse, damage caused by
fire or act of God, the use of voltages other than indicated
on the serial number plate of this product, or service of this
product by other than Oreck or an Oreck Factory
Authorized Service Center.
Oreck does not authorize any person or representative to
assume or grant any other warranty obligation in
connection with the sale of this product.
Oreck's limited warranty is valid only if you retain proof of
purchase from Oreck or an Oreck authorized retail dealer
of this product. If you purchase this product from any other
source, your purchase is "AS IS", which means that Oreck
grants to you no warranty and that you, not Oreck,
assume the entire risk of the quality and performance of
this product, including the entire cost of any necessary
servicing or repairs of any defects.
3
S H
Grounding Methods
GROUNDED
OUTLET BOX
GROUNDED
OUTLET
GROUNDING
PIN
Sketch A
Orbiter Model 400, 600 & 700 is
®
intended for Household Use.
Orbiter Model 550 is intended for
®
Commercial Use.
ADAPTER
METAL
SCREW
Sketch B