Lutron EcoSystem H Serie Guía De Mejores Prácticas Para La Instalación

LED Driver Installation
Best Practices Guide
EcoSystem H-Series
®
Driver Mounting
Mount driver flush against fixture to provide best heat transfer. Avoid mounting driver close to heat source such as the light source. Installer is responsible
for ensuring that the driver calibration point (t
Specification Submittal (Lutron
®
Stud Mounting
(Uses 8 – 32 Threaded Stud)
Correct
Incorrect
Installing or Servicing LED Driver or Light Engine
WARNING: Shock hazard. May result in serious injury or death.
Disconnect power before servicing or installing.
Driver Wiring
For proper wiring, follow wiring schematic on driver being installed. Driver photos are for reference only.
EcoSystem H-Series, K Enclosure
®
3.00 in (76 mm) W × 1.00 in (25 mm) H × 4.90 in (124 mm) L
Power Wiring
LDE Models
K Enclosure
1
GND
NEU
Power Input
(Line Voltage)
N/C
L
EcoSystem
E2
®
Digital Link
(Class 1 or
E1
Class 2) 2,3
1 All drivers can be grounded through the mounting tabs or studs. K-enclosure drivers may
be grounded by using the optional ground terminal.
2
Class 2 must be separated from Class 1 and line voltage wiring by the following: 0.25 in
(6 mm) or physical barrier. Please refer to Application Note #142 for further information.
3
EcoSystem Digital Link length is limited by the wire gauge used for E1 and E2 as follows:
®
EcoSystem Digital Link Wiring
®
Wire Gauge Digital Link Length (max)
18 AWG 550 ft
16 AWG 900 ft
14 AWG 1400 ft
12 AWG 2200 ft
Wire Size Digital Link Length (max)
2
0.75 mm 155 m
1.0 mm 2 207 m
1.5 mm 2 310 m
2
2.5 mm 517 m
2
4.0 mm 828 m
To EcoSystem Digital Link compatible devices
®
(up to 64)
) does not exceed the maximum rated temperature. For more information, refer to the EcoSystem
c
P/N 369832).
K Enclosures
Driver must be electrically grounded for proper performance and to meet UL
K enclosure mounting tabs, grounding should be accomplished by using paint-piercing mounting hardware to ensure
electrical connection through driver enclosure and fixture.
EcoSystem
1.18 in (30 mm) W × 1.00 in (25 mm) H × 14.25 in (362 mm) L
M Enclosure
NEU
Power Input
N/C
(Line Voltage)
L
EcoSystem
E2
®
Digital Link
(Class 1 or
E1
Class 2) 2,3
H-Series, M Enclosure
®
Load Wiring
Wire Gauge
18 AWG (0.75 mm
16 AWG (1.5 mm
14 AWG (2.5 mm
12 AWG (4.0 mm
N
N/C
L
E2
E1
Driver
terminals
N
N/C
L
Lutron Technical Support Hotline
®
E2 Lutron, ), and EcoSystem are registered trademarks of Lutron Electronics Co., Inc.
E1
NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts.
UL is a registered trademark of Underwriters Laboratories, Inc.
www.lutron.com
Tab Mounting
M Enclosure
and NEC requirements. When using
® ®
Wire Strip Length
For power, output, and digital terminals
(E1, E2).
5/16 in (8 mm)
Note: Some models are not rated Class 2; refer to label on
the driver being installed.
See table below
Maximum Lead Length
200 mA –700 mA 710 mA –1.5 A 1.51 A –2.10 A
2 ) 30 ft (9 m) 15 ft (4.5 m)
2
) 35 ft (10.5 m) 25 ft (7.5 m)
2
) 50 ft (15 m) 40 ft (12 m)
2 ) 100 ft (30 m) 60 ft (18 m)
P/N 041483a
12/2014
H-Series
®
Solid copper wire
18 –16 AWG
(0.75 –1.5 mm 2 )
–V (Black)
LED light source
+V (Red)
10 ft (3 m)
15 ft (4.5 m)
25 ft (7.5 m)
40 ft (12 m)
1.800.523.9466