Product Familiarisation; Unpacking Your Tool - Silverline 868245 Guia De Inicio Rapido

GB

Product Familiarisation

1 Palm Grip
2 ¼" BSP Bayonet Quick Connector
3 Guide Bush
4 Cap Exhaust

Unpacking Your Tool

• Carefully unpack and inspect your tool. Fully familiarise yourself with all
its features and functions
• Ensure that all parts of the tool are present and in good condition. If
any parts are missing or damaged, have such parts replaced before
attempting to use this tool
Air supply connection
• This tool is supplied with a ¼" Bayonet Quick Connector (2) fitted. Air
lines fitted with matching ¼" connectors are a push fit
• Do not allow supply pressure to exceed the maximum stated in the
specifications (above)
• Ensure that condensate is drained from air system daily
• Ensure that all parts of the system (hoses, couplers, etc) are correctly
rated for the air pressure to be used
Preparation
• Before using this tool for the first time and before each use, pour 4-5
drops/1.5ml of 30w non-detergent oil into the Air Inlet (2)
• Do not use detergent oils, oil additives or air tool oils; air tool oils may
contain solvents which will damage the tool's internal components
• After adding oil run the machine briefly. Wipe off any excess oil from the
Cap Exhaust (4)
Operation
1. Connect the tool to the air supply
2. Load fastener into the Guide Bush (3)
3. Hold tool in your palm with nose pointed towards the work surface
4. Align fastener and tool in location where fastener is to be driven
5. Push gently against nail head to drive fastener
6. Continue to apply pressure until fastener is driven completely or until
reaching desired penetration
PROBLEM
Air leaking between housing and cap
Air leaking through cap exhaust or nose area
Nailer not setting fastener completely
Nailer operates slowly or has loss of power
6
Operating notes
• Do not drive fasteners close to the edge of material. The workpiece may
• Disconnect tool from air supply if moving to new location. Do not carry
• During normal use, the tool will recoil immediately after driving a
• Do not drive fasteners on top of other fasteners or with the tool at an
• Do not activate the tool unless you intend to drive a fastener
Maintenance
• Disconnect the machine from the air supply before carrying out any
• Keep your machine clean at all times. Dirt and dust will cause internal
• Clean the body of your machine with a soft brush, or dry cloth
• After each use, pour approx 4-5drops/1.5ml of 30w non-detergent oil
• If the tool stops working, or only works intermittently, pour approx 1.5ml
POSSIBLE CAUSE
Loose screws in housing
Damage to cap gasket
Air escaping from tool
Damaged O-ring(s)
Nail guide loose;
Inadequate air flow to nailer
Nailer not lubricated sufficiently
Worn O-rings
Low air pressure
split, causing the fastener to ricochet, with consequent risk of personal
injury
the tool connected to the air supply; accidental discharge could result
fastener. This is a normal function of the tool. Do not attempt to prevent
the recoil by holding the tool against the work. Grip the handle firmly and
let the tool do the work
overly steep angle as this may cause deflection of fasteners, with risk of
personal injury
maintenance or cleaning
parts to wear quickly, and shorten the machine's service life
into the Air Inlet (2)
of non-detergent oil into the Air Inlet (2), and connect to air supply.
Operate the tool in short bursts. If this does not free the tool mechanism,
have the tool serviced at an authorised service centre
CORRECTIVE ACTION
Tighten screws
Replace cap gasket
Slap the cap into your palm with sufficient force to
re-set the internal piston
Replace O-ring(s)
Tighten guide bush
Check hose, fitting or compressor
Lubricate nailer
Replace and lubricate O-rings
Check and adjust pressure