Publicidad
Enlaces rápidos
I N S T A L L A T I O N
1
This product must be installed in accordance with the applicable installation code, by a person
familiar with the construction and operation of the product and the hazards involved. Ensure power
is off before installation, verify electrical plan first, read all installation instructions before beginning
installation. With the constant development of our products please check our website (www.modalight.com)
for any possible changes to the installation of this product.
Este producto debe ser instalado de acuerdo con el código de instalación por una persona familiarizada con la construcción y
operación del producto y los riesgos que entraña. Asegúrese que la electricidad este apagada antes de la instalación, verifique plan
electrico, lea todas las instrucciones de instalación antes de comenzar instalación. Con el desarrollo constante de nuestros productos,
visite nuestro website (www.modalight.com) para todos posibles cambios en la instalación de este producto.
Ce produit doit être installé en conformité avec le code d'installation applicable, par une personne familière avec la construction et
l'exploitation du produit et les risques encourus. Assurer que l'alimentation est coupée avant l'installation, vérifiez le plan électrique
d'abord, lire toutes les instructions d'installation avant de commencer installation. Avec le développement constant de nos produits s'il
vous plaît consulter notre site web (www.modalight.com) pour toutes les modifications possibles à l'installation de ce produit.
2
Verify electrical plan and ensure all hardware is present.
Verificar plan electrico y verifique que todo el equipo esté presente.
Vérifier le plan électrique et assurer que tout le matériel est présent.
10' Leader Cable
3
Wiring
Cablería
Cables
24v Driver
DMX Controller
Due to continuous improvements and innovations, specifications may change without notice.
Please refer to our website for current technical data. These figures are provided as a guideline
only and may vary with differing power supplies and installtions. All rights reserved. E&OE.
DRY LOCATION INSTALL
INSTALACIÓN DE LUGARES SECOS
EMPLACEMENT SEC INSTALLER
!
Max Continuous Run: 32' 9 7/10" (10m)
Continuidad Máxima: 32' 9 7/10" (10m)
Run Continue Max: 32' 9 7/10" (10m)
LD180
RGB FLATFLEX
Jumper Cable
955 White Drive Las Vegas, NV 89119 | T: 702 407 7775
F: 702 407 7773 | www.modalight.com | © Copyright 2018
®
End Cap
RGB Flatflex
VDC20181202
Publicidad
Manuales relacionados para Moda Light RGB FLATFLEX
Resumen de contenidos para Moda Light RGB FLATFLEX
- Página 1 RGB FLATFLEX ® I N S T A L L A T I O N This product must be installed in accordance with the applicable installation code, by a person familiar with the construction and operation of the product and the hazards involved. Ensure power is off before installation, verify electrical plan first, read all installation instructions before beginning installation.
- Página 2 RGB FLATFLEX ® I N S T A L L A T I O N Compatible driver list Lista de controladores compatibles Liste des pilotes compatibles Non Dimming Voltage Range Wattage IP Rating Max Load MP17 100-277v AC 150w IP67 48ft Screw in mounting clips.
- Página 3 RGB FLATFLEX ® I N S T A L L A T I O N Field cuttable at designated points Se puede cortar en los puntos designados Il peut être coupé à des points désignés Leader cable connection Conexión de cable de poder Connexion du cordon d’alimentation...
- Página 4 Slide end cap in RGB Flatflex and apply silicone. Coloque protector de luz en el interior tapa y llenar 1/3 con silicona. Deslice la tapa en el RGB Flatflex y aplique silicona. Placez Bouclier Lumière à l’intérieur de capuchon et remplissez 1/3 avec du silicone.
- Página 5 Connexions disponibles Press RGB FLATFLEX firmly into mounted clips. Presione RGB FLATFLEX firmemente en clips previamente instalados. Appuyez sur RGB FLATFLEX fermement dans les clips montés. Press RGB FLATFLEX firmly into mounted XTRUSION ® Presione RGB FLATFLEX firmemente en XTRUSION previamente instalados.
- Página 6 FPCB from dust H: 2/5” (11mm) L: 1 1/5” (30mm) Screws into surface W: 1/5” (6mm) Mounting Clip for RGB-FF-CLP to hold RGB FLATFLEX H: 3/10” (8mm) RGB FLATFLEX 2 Screws 1/2” (13mm) L: 3’ (914mm) Screws into surface 3’ RGB FLATFLEX W: 5/8”...
- Página 7 All MODA LIGHT products should be installed by a Licensed Electrician to local & national code. Do not modify, adapt or cut any MODA LIGHT components, plugs or accessories. Any modifications will void the warranty and may create a potential safety hazard. Do not put on the same circuit as inductive loads. Incorrect wiring will result in irreparable permanent damage to the LEDs and fixture. MODA LIGHT tests all products before shipping, and will not replace items that have been destroyed by incorrect wiring or handling.