Publicidad
Enlaces rápidos
I N S T A L L A T I O N
1
This product must be installed in accordance with the applicable installation code, by a person
familiar with the construction and operation of the product and the hazards involved. Ensure power
is off before installation, verify electrical plan first, read all installation instructions before beginning
installation. With the constant development of our products please check our website (www.modalight.com)
for any possible changes to the installation of this product.
Este producto debe ser instalado de acuerdo con el código de instalación por una persona familiarizada con la construcción y
operación del producto y los riesgos que entraña. Asegúrese que la electricidad este apagada antes de la instalación, verifique plan
electrico, lea todas las instrucciones de instalación antes de comenzar instalación. Con el desarrollo constante de nuestros productos,
visite nuestro website (www.modalight.com) para todos posibles cambios en la instalación de este producto.
Ce produit doit être installé en conformité avec le code d'installation applicable, par une personne familière avec la construction et
l'exploitation du produit et les risques encourus. Assurer que l'alimentation est coupée avant l'installation, vérifiez le plan électrique
d'abord, lire toutes les instructions d'installation avant de commencer installation. Avec le développement constant de nos produits s'il
vous plaît consulter notre site web (www.modalight.com) pour toutes les modifications possibles à l'installation de ce produit.
2
Verify electrical plan and ensure all hardware is present.
Verificar plan electrico y verifique que todo el equipo esté presente.
Vérifier le plan électrique et assurer que tout le matériel est présent.
10' Leader Cable
Install 12V Driver in a wet location enclosure.
3
Instale 12V Driver en un recinto de ubicación mojada.
Installez le pilote 12V dans un boîtier d'emplacement humide.
Due to continuous improvements and innovations, specifications may change without notice.
Please refer to our website for current technical data. These figures are provided as a guideline
only and may vary with differing power supplies and installations. All rights reserved. E&OE.
WET LOCATION INSTALL
INSTALACIÓN DE LUGARES HÚMEDOS
EMPLACEMENT HUMIDE INSTALLER
Max Continuous Run: 19' 8 1/5" (6m)
Continuidad Máxima: 19' 8 1/5" (6m)
Run Continue Max: 19' 8 1/5" (6m)
Enclosure must be 1.5 times the volume of the Driver to allow for proper air circulation.
El recinto debe ser 1.5 veces el volumen del Driver para permitir una circulación de aire adecuada.
L'enceinte doit être 1,5 fois plus volumineuse Driver pour permettre une bonne circulation de l'air)
Field Solder Jumper Cable
!
!
AQUAFLEX
955 White Drive Las Vegas, NV 89119 | T: 702 407 7775
F: 702 407 7773 | www.modalight.com | © Copyright 2018
RUBY
®
End Cap
VDC20182105
Publicidad
Manuales relacionados para Moda Light Aquaflex Ruby
Resumen de contenidos para Moda Light Aquaflex Ruby
- Página 1 AQUAFLEX RUBY ® I N S T A L L A T I O N This product must be installed in accordance with the applicable installation code, by a person familiar with the construction and operation of the product and the hazards involved. Ensure power is off before installation, verify electrical plan first, read all installation instructions before beginning installation.
- Página 2 I N S T A L L A T I O N Non-Dimming Wiring Cablería sin atenuación Câblage sans gradation 100-277V AC DRIVER INPUT DRIVER OUTPUT AQUAFLEX RUBY UL / cUL INPUT (100-277V AC) OUTPUT (12V DC) Positive Positive Negative...
- Página 3 AQUAFLEX RUBY ® I N S T A L L A T I O N Compatible driver list Lista de controladores compatibles Liste des pilotes compatibles Non Dimming Voltage Range Wattage IP Rating Max Load MP16 100-277v AC 132w IP67 54ft 0-10v Dimming Voltage Range...
- Página 4 AQUAFLEX RUBY ® I N S T A L L A T I O N Field cuttable at designated points Corte en los puntos designados Il peut être coupé à des points désignés Leader cable connection Conexión de cable de poder Connexion du cordon d’alimentation Make a small incision on the back of the end cap.
- Página 5 SIZE ITEM NO. L: 1 1/5” (30mm) Screws into surface to W: 1/5” (5mm) MRTA61 Mounting Clips hold AQUAFLEX RUBY H: 1/5” (5mm) 2 Screws 1/2” (13mm) L: 3/5” (15mm) Terminates AQUAFLEX RUBY End Cap W: 1/5” (5mm) to protect FPCB MRTA63 H: 1/5”...
- Página 6 All MODA LIGHT products should be installed by a Licensed Electrician to local & national code. Do not modify, adapt or cut any MODA LIGHT components, plugs or accessories. Any modifications will void the warranty and may create a potential safety hazard. Do not put on the same circuit as inductive loads. Incorrect wiring will result in irreparable permanent damage to the LEDs and fixture. MODA LIGHT tests all products before shipping, and will not replace items that have been destroyed by incorrect wiring or handling.