Instalation; Transport And Discharge; Arrangement Of The Lighting System; Arrangement Of The Pneumatic System - Elcometer SAGOLA S25 Manual De Instrucciones

INCORRECT INSTALLATION OF THE MACHINE
MAY CAUSE DAMAGE TO PEOPLE, ANIMALS OR
OBJECTS. THE MANUFACTURER CANNOT BE
CONSIDERED RESPONSIBLE
DAMAGES.

7.1 TRANSPORT AND DISCHARGE

The equipment Aquaplastic is delivered packaged. It
must be transported and stored according to the
indications on the packaging.
Due to the low weight of the equipment Aquaplastic
can be moved by two people without using other
means.

7.2 ARRANGEMENT OF THE LIGHTING SYSTEM

The Client must make sure that there is suitable
lighting for the surroundings and that the lighting
conforms to the regulations in force. In particular, the
Client must arrange the positioning of lighting that
illuminates all the working area.
7.3 ARRANGEMENT
SYSTEM
The Client must arrange a line of filtered compressed
air supplied by a compressor that is suitable for the
consumption required. Do not use compressed air
that contains chemical products, synthetic oil with
organic solvents, salts or corrosive gases as they
can cause damage or malfunctioning. The line of
compressed air must arrive up to the supply points of
the machine. If the compressed air contains a large
amount of moisture, it may cause malfunctioning in
the valves and in the pneumatic components. Install
a moisture separator downstream from the compres-
sor to avoid this.
7.4. CLASSIFICATION ACCORDING TO THE ATEX
DIRECTIVE
The machine conforms to the essential requisites of
the EU Directive 2014/34/UE, better known as ATEX
("Explosive atmospheres"). It is classified as group II
category 3 letter G system. The assessment proce-
dures of conformity, carried out by an internal factory
check, allow the installation of the machine in
surroundings where there may be potentially explosi-
ve atmospheres due to the presence of gas, fumes
or mist.
Preparation for extraction of gases
For the compliance ATEX, the machine is equipped
with a system of forced evacuation of the fumes
generated during the operation.
The smoke evacuation takes place through a chim-
ney on the upper end of the machine and is powered
by a forced suction (venture effect) that is automati-
cally activated depending on the mode of operation
of the machine.

7. INSTALATION

FOR THESE
OF THE PNEUMATIC
This chimney must then be connected to the general
workshop extraction or brought outside the works-
hop.
In this second case, the chimney connected to the
machine must cover at least a portion in the vertical
of 1 meter before being led outside.
For an easy installation, the chimney is generally an
aluminum tube, flexible and extensible.
The fumes of solvent dispersed in that way do not
need further treatment.

7.5. POSITIONING

The S25 must be positioned in a well-aired place.
The area must be equipped with all means provided
by the european legislation related to the health and
safety of the workers in the workplace.
Position the machine on the floor and make sure that
there is sufficient space around the machine to carry
out normal maintenance operations or inspections.

7.6. PUTTING INTO USE

1. Connect the grounding cable (nº9) provided with
the machine and marked yellow/green from the side
of the cable lug to the hole (nº6) at the base of the
machine, and connect the other side of the groun-
ding cable with free terminal to the earth contact of
the electrical supply.
2. Make sure that the on/off switch (nº18) of the
machine is in the off position.
3. Connect the quick coupling of the machine's (nº7)
air supply to the compressed air supply (max. 7 bar).
4. Place a clean solvent drum under the machine.
Then insert the suction filter (nº1) and the drain hose
(nº2) inside the drum.
5. Dismantle the gun and empty the canister into a
suitable recipient. Raise the lid of the automatic
washing tank.
6. Press the trigger of the spray gun and use the
nylon clip (nº16) to block the trigger of the spray gun.
- 16 -