Tabla De Contenido; Safety Information; Warranty; Pre-Installation - ETI aL-90-850-MV Guía De Uso Y Cuidado

Table of Contents
Table of Contents ......................................2
Safety Information ....................................2
Warranty ...................................................2
Pre-Installation .........................................3
Planning Installation ..............................3
Tools Required .......................................3

safety information

WarninG: Carefully read and understand the information
given in this manual before beginning the assembly and
installation. Failure to do so could lead to electric shock, fire,
or other injuries which could be hazardous or even fatal.
WarninG: Ensure the electricity to the wires you are
working on is shut off. Either remove the fuse or turn off the
circuit breaker.

Warranty

This product is warranted for a period of 5 years from the date of original purchase against defects in materials and
workmanship. If this product should fail to operate due to defects in material or workmanship within 60 months of
purchase, see www.ETiSSL.com for details. This product will be repaired or replaced, at ETi's option. This warranty
is expressly limited to repair or replacement of product and liability for direct, incidental, or consequential damages
is hereby expressly excluded. Some states do not allow exclusions of direct, incidental or consequential damages,
so the above limitation of exclusion may not apply to you. This warranty gives the consumer specific legal rights,
which vary from state to state. WARRANTY IS VOID IF PRODUCT IS NOT USED FOR THE PURPOSE WHICH THIS
PRODUCT IS MANUFACTURED.
Package Contents ..................................3
Hardware Included .................................3
Installation ................................................4
Maintenance .............................................7
Care & Cleaning ........................................8
Troubleshooting ........................................8
nOTiCe: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a partic-
ular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
□ Reorient or relocate the receiving antenna.
□ Increase the separation between the equipment and the receiver.
□ Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
□ Consult the dealer or an experienced radio/TV technician for help.
WarninG: Changes or modifications not expressly approved
by the party responsible for compliance could void the user's
authority to operate the equipment.
2

Pre-installation

PLANNING INSTALLATION

Before beginning assembly, installation, or operation of the product, make sure all parts are present. Compare parts
with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to
assemble, install, or operate the product. Contact Customer Service for replacement parts.
nOTe: Keep your receipt and these instructions for proof of purchase.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the
installation.

TOOLS REqUIREd

Wire
Safety
Strippers
Goggles
Wire Electrical
Cutters Tape
Silicone
Sealant

PACKAGE CONTENTS

Part description quantity
A LED Area Light 1

HARdWARE INCLUdEd

nOTe: Hardware not shown to actual size.
Part description
AA Wire Connector
BB Hexagon Socket Mounting Screw
CC Mounting Template
DD Pole Clamp (for optional pole
mount installation only)
EE Allen Wrench (M6)
FF Allen Wrench (M8)
Ladder
Power Drill
with Drill BIts
A
quantity
AA BB
3
3
1
CC
1
1
1
EE
3
Please contact 1-855-384-7754 for further assistance.
Gloves
Power Tool
Hex Bit
DD
FF
www.ETiSSL.com