Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
Instruction Manual
for Outdoor Light
230054
Please read carefully and keep for further reference !
1.
Use as directed:
This product serves exclusively lighting purposes and may:
only be used with a voltage of 230V ~50Hz.
not be used indoors.
not be exposed to strong mechanical loads or to strong
contamination.
only be installed and operated after a condition inspection if the
product is dirty or has been moistened through storage.
not be modified or converted.
If these points named above are not adhered to, a short circuit or
electrical shock may occur!
2.
Technical Data:
Operating voltage:
230V ~50Hz
Ignition voltage:
5 kV
Safety class:
I
Safety type:
IP 65
Bulb:
HIT/HIT-C, G12, 70W
Dimensions (W/H/D):
27 / 27 / 24 cm
Rotary-/Swivel range:
120°/ 120°
Weight:
5,4 kg
Importeur:
SLV Elektronik GmbH
IP 65: Protection against dust(dust-tight) - Protection against jetted water
from all directions
3.
Installation
The electric connection may be executed only by an electric expert
who is familiar with the valid directives!
Attention: Switch off the power of the mains supply line or
respectively of the connection lead before doing any works
parts, which are supplied with the product or are described as accessories!
Otherwise the product or the installation might not be sufficiently safe.
Installation place:
The product is suited for installation on the wall, ceiling and floor.
Make sure that the product is mounted on a stable, even and tilt-fixed
background.
The light exit should be placed at least so far from the illuminated surface,
as indicated as minimum distance on the type plate of the luminaire:
. Pay special caution to easily inflammable objects (e.g.
foliage).
Separate Installation Steps
Remove the front part of the lamp head by loosening the four screws (1).
Determine the place of installation and mark the holes to be drilled. Note
that the cable outlet of the power supply line fits between the mounting
bracket and the canopy. Do not damage the power supply line, e.g. by
drilling, screws or strong bending.
Fasten the mounting plate to the mounting surface (2).
Direct the connection lead in sufficient length through the cable
screwing. Secure the cable screwing (3).
Electrical Connection (4)
The product must be able to be separated by an all pole separation
from the current supply.
For electric connection attach the black or brown wire (live conductor)
of the mains supply with the clamp L and the blue wire (neutral
conductor) of the mains supply with the clamp N. The green-yellow
wire (protective conductor) of the mains supply has to be tightly
screwed into the earth clamp
Inserting the bulb: Use a piece of fabric to insert the bulbs. Do not
touch them with bare fingers. It takes about five minutes until the lamp
reaches its full potential. After switching it off, wait 5 to 10 minutes to let
the bulb cool down before restarting it.
Reattach the front part of the lamp head. Note that the gasket fits
correctly and gets evenly squeezed. Tighten the screws cross-wise.
Ensure that the light fixture holds securely!
The product is now ready for operation.
4.
Operation
:
Information for the user:
Operate the product only if it is working correctly. Switch off the product
with a malfunction immediately and operate it again only after examination
by an electrical specialist. This is the case, when:
visible damages appear.
the product does not work.
smoke, steam or crackling sounds appear.
an overheating is recognisable.
Repairs of the product or work on mains voltage-prominent sections may
only be carried out by qualified electricians.
Attention: Here exists mortal danger from an electric shock!
How to avoid failure and fire risk:
Do not cover the product - provide free air circulation!
Do not hang or fasten anything on the product, especially no decoration.
Replace damaged protection glasses immediately!
Never let children play unsupervised with electric products! Children
can not always estimate dangers in dealing with electric energy correctly.
The following enviromental influences may have unwanted effects on
the surface of the product:
acid rain and sour soil
thawing salt
other chemical substances (e.g. herbicides)
Protect the product by adequate means to avoid unwanted changes of the
.
Use only
surface. Cleaning tip: Switch off power! Clean the product with a damp
cloth.
What is to do if a bulb is defect or does not work?
Disconnect the product from power, before you exchange the bulbs.
Caution: Let the bulb cool down first before replacement – otherwise
considerable risk of injury exists because of the hot surface.
Replace the bulbs only with bulbs of the same data like socket, power
and capacity. Every other sort of bulb can lead to damages of the light.
Replacing the bulb: see Installation.
5.
What else has to be considered?
Disconnect the product from power, before you...
clean or maintain the product.
do any works on the product or its components (electric expert).
02/2007 © by SLV Elektronik GmbH
230054
Technical Details are subject to change.
of the product.
high salt content in the air
cleaning agents
Duplication prohibited !
1
1
L
N
4
2
3
2
Publicidad
