VONROC S VC503DC Traducción Del Manual Original página 8

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 25
EN
When the machine is not being used over a
longer period of time it is best to store the
battery in charged condition.
Assembly of the nozzles (Fig. D)
Either assembly the nozzles (9, 10 or 12) directly to
the suction opening (13) of the machine or use the
extension tube (8).
Floor nozzle (12)
The floor nozzle is designed for domestic dry
vacuuming in, for example, the house, workroom,
or car.
Joint nozzle (10)
The joint nozzle is designed for domestic dry
vacuuming, edges and other areas that are difficult
to access.
Cushion nozzle (9)
The cushion nozzle is designed for domestic dry
vacuuming, for example cushion of sofa's or textile
furniture.
Accessories holder for storage (11)
Put the vacuum cleaner accessories in the provided
holder on the vacuum cleaner.
4. OPERATION
Note: Regular emptying of the dust cup and
cleaning of the filter assembly ensures optimal
vacuum capacity.
Switching the machine on/off (Fig. A)
• To switch on the vacuum cleaner, move the On/
Off switch (2) forwards (direction ON).
• To switch off the vacuum cleaner, move the On/
Off switch (2) backwards (direction OFF).
5. MAINTENANCE
Before cleaning and maintenance, always
switch off the machine and remove the
battery pack from the machine.
Clean the machine casings regularly with a soft
cloth, preferably after each use. Make sure that
the ventilation openings are free of dust and
dirt. Remove very persistent dirt using a soft
cloth moistened with soapsuds. Do not use any
8
solvents such as gasoline, alcohol, ammonia, etc.
Chemicals such as these will damage the synthetic
components.
Cleaning the Dust Cup (Fig. E1, E2)
To maintain the optimum performance of the vacuum
cleaner, clean the dust cup (7) after each use.
• Press release button (2) and remove the dust
cup (7) from the motor housing (6).
• Remove the filter assembly (14) from the dust
cup.
• Shake/tap out the dust cup (7) over a suitable
waste bin.
If required, clean the dust cup with a moist cloth.
If required, clean the filter assembly (see
"Cleaning the Filter Assembly").
• Reinsert the filter assembly (14) into the dust
cup (7).
Afterwards, hang the dust cup at the bottom into
the motor housing, apply light pressure until the
dust cup can be heard to engage.
Cleaning the Filter Assembly (Fig. F1, F2)
• Press release button (2) and remove the dust
cup (7) from the motor housing (6).
• Remove the filter assembly (14) from the dust
cup.
• Remove the filter cover part 1 (15) from the
filter seal (16).
• Remove the filter cover part 2 (22), take out the
filter (17) out of filter cover part 1 (15).
If necessary, you can wet clean the filter (17):
Clean it under running water without any
cleaning detergent, squeeze out the filter (17)
and allow the filter to dry well in order to avoid
the formation of mould.
• Assembly is carried out in reverse order.
MALFUNCTIONS
In the case of insufficient vacuuming performance,
check the following:
1. Is the dust cup (7) full?
• See "Cleaning the Dust Cup".
2. Is the fabric filter (17) clogged with dust?
• See "Cleaning the Filter Assembly".
3. Is the capacity of the battery pack too low?
• See "Checking the battery charging status".
Regular emptying of the dust cup (7) and cleaning
of the filter assembly (14) ensures optimal vacuum
capacity.
WWW.VONROC.COM

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

S2 vc503dcS3 vc503dcVc503dc

Tabla de contenido