EDM Product 08708 Manual De Instrucciones página 16

HEAT GUN 2000W
OPERATING INSTRUCTIONS
This product is intended for removing paint, forming and
bending of plastic tubes, and the warming of
heat-shrinkable tubing, using the respective nozzles. The
product is also suitable for soldering and tinning, loosening
adhesive joints and defrosting water pipes.
This product must not be used on clothing or drying the hair
WARNING
Do not touch the nozzle as it becomes very hot during use
and remains hot for up to 30 minutes after use.
1. Check the product, its power cord and plug as well as
accessories for damage before each use. Do not use the
product if it is damaged or shows wear.
2. Double check that accessories or attachments are
properly fixed >Always hold the product by its handle. Keep
the handle dry and clean to ensure safe support.
3. Ensure that the air vents are always unobstructed and
WARNING
During operation fumes will be generated! Some fumes and
dust are highly inflammable and explosive! Do not smoke
during operation, keep heat sources and open flames out of
the working area! Always wear an approved dust mask to
protect yourself against hazards resulting from fumes and
fine dust
6. Do not touch hot air outlet or accessory tips. Contact with
the hot air outlet or accessory tip could result in personal
injury.
7. Place the product on its stand in a clear area away from
combustible materials while cooling to prevent materials
from igniting.
8. Work in a well-ventilated area, open windows and put an
exhaust fan in the room. Be sure the fan is moving air from
inside to outside. Proper ventilation will reduce the risk of
inhaling chemicals found in the fumes or dust created by
using this product.
9. Work in one room at a time. Remove furnishings or cover
them and place in the centre of the room. Seal doorways
with drop cloths to seal work area from the rest of the
building.
10. Remove or protect any carpets, rugs, furniture, clothing,
cooking utensils and air ducts to prevent contamination and
property damage from the paint scrapings. Paint scrapings
may ignite if too close to the nozzle.
11. Place dust sheets in the work area to catch paint
scrapings.Wear protective clothing such as hats, extra work
EN INSTRUCTION MANUAL
or other body parts of pets and humans. For safety reasons it
is essential to read the entire instruction manual before first
operation and to observe all the instructions therein.
This product is intended for private domestic use only, not
for any commercial trade use. It must not be used for any
purposes other than those described.
clear. Clean them if necessary with a soft brush. Blocked air
vents may lead to overheating and damage the product.
4. Switch the product off immediately if you are disturbed
while working with it and when other people enter the
working area. Always let the product come to complete stop
before putting it down.
5. Do not overwork yourself. Take regular breaks to ensure
you can concentrate on the work and have full control over
the product.
shirts and overalls. Paint scrapings may contain chemicals
that are hazardous.
12. Becareful when working until the proper combination of
heat, distance and time of application has been obtained.
Use a back and forth motion when applying heat unless
concentrated heat is desirable. Pausing or lingering in one
spot may ignite or melt the work piece or the material
behind it.
13. Do not use this product to remove paint containing
lead.The peelings, residue and vapour sofpaint may contain
lead, which is poisonous. Any pre-1960 building may have
been painted in the past with paint containing lead and
covered with additional layers of paint. Once deposited on
surfaces, hand to mouth contact can result in the ingestion
of lead. Exposure even to low levels of lead can cause
irreversible damage to the brain and nervous system. Young
and unborn children are particularly vulnerable.
14. When removing paint, ensure the work area is enclosed.
Wear a dustmask.
15. Do not burn the paint. Use the scraper and keep the
nozzle at least 25mm away from the painted surface.
When working in a vertical direction, work downwards to
prevent paint from falling into the product and
burning.
16. Dispose of all paint debris safely and ensure the work
area is thoroughly cleaned after completing the work.
REF. 08708