Publicidad
Idiomas disponibles
Idiomas disponibles
Prior to
Installation
EN
installation
Please remove the battery seal from the battery compartment. Install the
of the engine compartment
so that the area of diffusion of the ultrasonic speaker is as large as possible and
the device is protected from excessive heat, water and dirt. We recommend positioning the device so that the
area of diffusion is directed downwards from above. For clarification: Imagine the area of diffusion is the beam
of a torch, which needs to illuminate the largest area possible. We recommend using the optional mounting
bracket (item code 07599).
We recommend installing the device in the upper third of the engine compartment since martens, due to
their burrowing behaviour, instinctively make their way up through the engine cavity. Moreover, this facilitates
installation and ensures that all of the components are better protected from dirt.
Prior to
Installation
installation
After installing the ultrasonic device, we recommend retesting the device to ensure that it functions correctly.
Perform the test using an ultrasonic tester (Item code. 07595). If the function check is successful but ul-
trasound is not emitted after installation, an installation error has occurred.
Blinking at regular intervals (approx. every 5 seconds) = OK: Ultrasound is being emitted.
LED off = device is switched off.
Prior to
Installation
installation
1.
Do the button batteries (CR 2477) have a voltage of at least 3 volts? Regular testing of
the battery voltage is recommended.
2.
Is the engine switched off?
3.
Is the device completely still and not subject to any movement or vibration?
Prior to
Installation
installation
Function control light
*Switching the device on and off
Pull the slide contact (printed part) half way out.
Changing the CR 2477 battery
Pull the slide contact (printed part) out completely. When inserting the batteries, pay attention to the polarity.
The printed plus side of the battery should face upwards so that the plus sign is visible after insertion of the
button battery. Push the slide contact back in, keeping it straight!
8
Function
Trouble
Circuit
check
shooting
diagram
ultrasonic device in the upper third
Function
Trouble
Circuit
check
shooting
diagram
Function
Trouble
Circuit
check
shooting
diagram
Function
Trouble
Circuit
check
shooting
diagram
Speaker housing
Slide contact*/
battery compartment
CR2477
Prior to
Warranty
installation
IMPORTANT! Terms of the warranty (please keep in a safe place)!
Our 4B Battery-operated ultrasonic device comes with a 48-month functional warranty.
1.
Any reasonable complaints within the warranty period from the date of purchase will be remedied free
of charge, either through repair or delivery of a replacement product at our discretion. In order for the
warranty to apply, our product must have been properly installed and maintained in accordance with
our installation instructions.
2.
To enable us respond to problems, please return the complete unit, including the batteries and installati-
on invoice, initially at your own expense. Once the problem has been resolved, the product
will be returned to you free of charge.
3.
We are not liable for any further claims, such as costs for installing/deinstalling the unit. Any claim
under Section 5 of our General Terms and Conditions shall remain unaffected, subject to the conditions
Warranty
set out therein.
4.
Any damage caused by improper installation or incorrect, negligent or forceful operation shall invalidate
the warranty. There shall be no liability for consequential damage.
Technical changes and errors excepted.
Please fill in to claim against the warranty: For warranty claims to be processed, you must send us the filled
in coupon and the garage/installation invoice!
Warranty
Garage stamp
Warranty
Date of purchase
Technical support hotline
+49 (0) 7631 9727-80
Service address
Norbert Schaub GmbH
Robert-Koch-Strasse 20
79395 Neuenburg am Rhein
GERMANY
Tel. +49 (0) 7631 9727- 0
Fax +49 (0) 7631 9727-27
info@stop-go.de
www.stop-go.de
Function
Trouble
Installation
check
shooting
Circuit
Warranty
EN
diagram
Unit serial number
9
Publicidad
