OttLite 15486RBS Guia De Inicio Rapido

C
C
D
D
E
E
F
F
B
G
B
G
15w Provo Table Lamp
A
15484RBS
INS1 10015 1 1 181 1
15w Provo Table Lamp
15w Provo Table Lamp
15486RBS 15484RBS
15484RBS
INS-14-0117
H
H
I
I
J
J
A
ENGLISH
PRODUCT REGISTRATION FORM
Please complete the enclosed Product
CONGRATULATIONS!
Registration Form and return it today by mail,
You've purchased the finest in natural lighting
or register online by going to:
technology with your new OttLite
English
www.OttLite.com/warranty.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product
CONGRATULATIONS!
WARNING: To prevent electric shock, make
Registration Form and return it today by mail,
You've purchased the finest in natural lighting technology
sure the lamp is not plugged in until all
or register online by going to:
with your new OttLite product.
www.OttLite.com/warranty. ®
assembly steps are complete.
PRODUCT REGISTRATION FORM
WARNING: To prevent electric shock, make
LAMP ASSEMBLY
Please complete the enclosed Product Registration Form
sure the lamp is not plugged in until all
1. Unpack all lamp parts and lay out on
assembly steps are complete.
and return it today by mail, or register online by going to:
OttLite.com/warranty. the floor with the base (A) laying flat.
LAMP ASSEMBLY
1. Unpack all lamp parts and lay out on
WARNING! To prevent electrical shock, make sure
2. Thread lower pole (B) to base (A) by
the floor with the base (A) laying flat.
the lamp is not plugged in until all assembly steps
hand turning clockwise until tight.
are complete.
2. Thread lower pole (B) to base (A) by
LAMP ASSEMbLy hand turning clockwise until tight.
3. Attach shade (E) to socket cup (D)
Unpack all lamp parts and lay out on the floor with the
1.
3. Attach shade (E) to socket cup (D) using socket ring (F) to hold shade in place.
base (A) laying flat.
using socket ring (F) to hold shade in place.
2. Thread lower pole (B) to base (A) by hand turning
4. Thread socket ring (F) in socket cup (D)
4. Thread socket ring (F) in socket cup (D)
clockwise until tight.
by turning clockwise until tight enough to
by turning clockwise until tight enough to
Attach shade (E) to socket cup (D) using socket ring
3.
hold the shade steady.
hold the shade steady.
(F) to hold shade in place.
Thread socket ring (F) in socket cup (D) by turning
4. 5. To postion the shade (E), loosen thumbscrews
5. To postion the shade (E), loosen thumbscrews
(C). Move shade (E) into position, then tighten clockwise until tight enough to hold the shade steady.
(C). Move shade (E) into position, then tighten
thumbscrews (C) by hand until snug.
5. To postion the shade (E), loosen thumbscrews
thumbscrews (C) by hand until snug.
(C). Move shade (E) into position, then tighten
DO NOT force thumbscrew as damage to the
thumbscrews (C) by hand until snug. DO NOT force
lamp may occur.
DO NOT force thumbscrew as damage to the
thumbscrew as damage to the lamp may occur.
lamp may occur.
6. Install bulb following BULB
6. Install bulb following BULB INSERTION/
INSERTION/REPLACEMENT instructions.
REPLACEMENT instructions.
6. Install bulb following BULB
Adjust height of pole (H) by turning knob (I) counter
7.
7. Adjust height of pole (H) by turning knob (I)
clockwise until desired height. To tighten, turn knob (I) INSERTION/REPLACEMENT instructions.
counter clockwise until desired height. To tighten,
clockwise.
turn knob (I) clockwise.
7. Adjust height of pole (H) by turning knob (I)
counter clockwise until desired height. To tighten,
CAUTION! IMPORTANT SAFETY INSTRUCTIONS:
CAUTION! IMPORTANT SAFETY INSTRUCTIONS: turn knob (I) clockwise.
THIS PORTABLE LAMP HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER) AS A FEATURE TO REDUCE THE RISK OF
ELECTRIC SHOCK. THIS PLUG WILL FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF THE PLUG DOES NOT FIT FULLY IN THE OUTLET,
THIS PORTABLE LAMP HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER) AS A FEATURE TO REDUCE THE RISK OF ELECTRIC
SHOCK. THIS PLUG WILL FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF THE PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE
CAUTION! IMPORTANT SAFETY INSTRUCTIONS:
REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A QUALIFIED ELECTRICIAN. NEVER USE WITH AN EXTENSION CORD UNLESS
PLUG. IF IT STILL DOES NOT FIT, CONTACT A QUALIFIED ELECTRICIAN. NEVER USE WITH AN EXTENSION CORD UNLESS PLUG CAN BE FULLY
PLUG CAN BE FULLY INSERTED. DO NOT ALTER THE PLUG.
INSERTED. DO NOT ALTER THE PLUG.
THIS PORTABLE LAMP HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER) AS A FEATURE TO REDUCE T
IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE
CAUTION:
MANUFACTURER OR ITS SERVICE AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD. INDOOR USE ONLY.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ELECTRIC SHOCK. THIS PLUG WILL FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF THE PLUG DOES NOT FIT FULLY IN
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A QUALIFIED ELECTRICIAN. NEVER USE WITH AN EXTENSION
This product complies with Part 18 of FCC Rules, but may cause interference to radios, televisions, wireless telephones, and remote controls.
CAUTION!
S2427
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or its service agent or a
Avoid placing this product near these devices. If interference occurs, move the product away from the device or plug either into a different
PLUG CAN BE FULLY INSERTED. DO NOT ALTER THE PLUG.
similar qualified person in order to avoid a hazard. Indoor use only.
outlet. Do not install this product near maritime safety equipment or other critical navigation or communication equipment operating between
0.45-30 MHz.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
This Class B RFLD complies with Canadian ICES-005
S2427
CAUTION!
S2427
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or i
similar qualified person in order to avoid a hazard. Indoor use only.
Provo Table Lamp
9. To turn the lamp on or off, toggle
cord mounted switch (J).
8. Plug the lamp into a standard 120V
BULB INSTALLATION AND REMOV
product. outlet.
®
1. Make sure the lamp is not plugged
9. To turn the lamp on or off, toggle the power
electrical socket.
cord mounted switch (J).
8. Plug the lamp into a standard 120V outlet.
9. To turn the lamp on or off, toggle the power cord
2. If the lamp has been in use, allow
BULB INSTALLATION AND REMOVAL
mounted switch (J).
1. Make sure the lamp is not plugged into an
approximately 5 minutes before proc
electrical socket.
bULb INSERTION/REPLACEMENT
3. To install the bulb (G) in the socke
1. Make sure the lamp is not plugged into an electrical
2. If the lamp has been in use, allow it to cool
the base of the bulb into the socket
approximately 5 minutes before proceeding. socket.
clockwise until snug.
If the lamp has been in use, allow it to cool for
2.
3. To install the bulb (G) in the socket (D), thread
approximately 5 minutes before proceeding.
the base of the bulb into the socket (D) turning
CAUTION: DO NOT over tighten th
To install the bulb (G) in the socket (D), thread the
3.
clockwise until snug.
base of the bulb into the socket (D) turning clockwise
tightening the bulb may make rem
CAUTION: DO NOT over tighten the bulb. Over
until snug.
or damage the lamp or bulb.
tightening the bulb may make removal difficult
CAUTION: DO NOT over tighten the bulb. Over
or damage the lamp or bulb.
tightening the bulb may make removal difficult or
4. To remove a bulb (G) already insta
damage the lamp or bulb.
4. To remove a bulb (G) already installed in the
lamp, unthread the bulb from the soc
4. To remove a bulb (G) already installed in the lamp,
lamp, unthread the bulb from the socket (D) turn-
ing counterclockwise to loosen.
ing counterclockwise to loosen. unthread the bulb from the socket (D) turning
counterclockwise to loosen.
Please note that in operation, OttLite
Please note that in operation, OttLite
not dimmable. Enjoy your OttLite 15w Provo Table Lamp!
not dimmable.
Please note that in operation, OttLite tubes are not
Enjoy your OttLite Provo Table lamp!
®
Enjoy your OttLite
dimmable.
This lighting system is designed for use with
This lighting system is designed for use with OttLite
OttLite type (Style Number ED15-S). Use
®
This lighting system is designed fo
type (Style Number ED15-S). Use of other products
of other products voids the warranty and may
OttLite
result in damage to the lighting system. voids the warranty and may result in damage to the
of other products voids the warran
lighting system.
result in damage to the lighting sy
15w Provo Table Lamp
tubes are
®
Provo Table lamp
®
®
type (Style Number ED1
®
REV071614