OttLite 15548BB8 Guia De Inicio Rapido

Ocultar thumbs

página de 2

/ 2
Marcadores

Enlaces rápidos

Descargar este manual

15w Cambridge Table Lamp

15548BB8

15548BZH

15548BZP

15548BB8

REV022111

ENGLISH

CONGRATULATIONS! You've

purchased the finest in natural lighting

technology with your new OttLite

product.

PRODUCT REGISTRATION FORM

Please complete the enclosed Product

Registration Form and return it today

by mail, or register online by going to:

http://warranty.OttLite.com.

WARNING: To prevent electric shock,

make sure the lamp is not plugged in

until all assembly steps are complete.

To avoid lamp tip over, position lamp

shade as shown in diagram.

LAMP ASSEMBLY

1. Remove lamp from packing placing

the base (A) flat on a steady surface.

2. Loosen, but do not remove, thumb-

2. Thread pole (B) to base (A) by hand,

screw (D) at the joint on arm (E).

turning clockwise until snug. Excess

cord may be pulled through the base.

3. To aid in assembly of step 6, rotate

the joint so that it points opposite to the

3. Attach counterbalance (C) to arm (E)

arm (E). Tighten thumbscrew (D) by hand

by turning clockwise until snug, then

until snug.

finish threading arm (E) into pole (B).

4. Thread pole (B) to the joint of arm (E)

4. Fit shade (H) over socket (G) then

by hand carefully turning clockwise. DO

thread socket ring (J) onto socket.

NOT tighten completely.

Turn socket ring (J) clockwise to tight-

en until finger tight and the shade (H)

5. Hold arm (E) to steady pole (B) then

is held securely.

thread pole (B) to base (A) by hand care-

fully turning clockwise until snug. Arm (E)

5. Refer to BULB INSERTION/

will still be loose. Excess cord may be

REMOVAL to install bulb (K) in lamp.

pulled through the base (A).

6. Plug the cord into a standard 120Vac

6. Finish threading arm (E) to pole (B) by

outlet.

hand turning clockwise until snug.

7. To turn the lamp ON or OFF rotate the

7. Attach shade (H) to socket housing (G)

switch (M) clockwise.

using socket ring (J) to hold the shade in

place.

8. To position the upper arm (E), turn

thumbscrew (D) counterclockwise to

8. Thread socket ring (J) onto socket by

loosen, reposition arm (E) then turn

hand turning clockwise until tight enough

thumbscrew (D) clockwise to tighten.

to hold the shade steady.

To avoid damage to the lamp, DO

NOT ATTTEMPT to move arm (E)

9. Thread arm (C) into joint of pole (E) by

without loosening thumbscrew (D).

hand turning clockwise until tight.

9. DO NOT try to rotate the shade side-

10. Refer to BULB INSTALLATION AND

ways as the lamp maybe damaged.

REMOVAL to install bulb (K) in lamp.

CAUTION!

If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufac-

turer or its service agent or a similar qualified person in order to avoid a hazard. Indoor use only.

S2471

turer or its service agent or a similar qualified person in order to avoid a hazard. Indoor use only.

ST10086

15w Cambridge Table Lamp

Cambridge Table Lamp

11. Plug the cord into a standard 120Vac

DO NOT force thumbscrew as damage

outlet.

to the lamp may occur.

12. To turn the lamp on or off rotate the

BULB INSERTION/REMOVAL

power cord mounted switch (M)

1. Make sure the lamp is not plugged into

clockwise.

an electrical socket.

13. To position arm (E) turn thumbnut (D)

2. If the lamp has been in use, allow it to

counterclockwise to loosen, reposition

cool approximately 5 minutes before

arm (E) then turn thumbnut (D) clockwise

proceeding.

to tighten. To avoid damage to the lamp

DO NOT ATTEMPT to move arm (E)

3. To install the bulb (K) in the socket (G),

without loosening thumbnut (D).

thread the base of the bulb into the

socket turning clockwise until snug.

14. DO NOT try to rotate the shade side-

ways as the lamp maybe damaged.

CAUTION: DO NOT overtighten the

bulb. Overtightening the bulb may

DO NOT force thumbscrew as damage

make removal difficult or damage

to the lamp may occur.

the lamp or bulb.

BULB INSERTION/REMOVAL

4. To remove a bulb (K) already installed

1. Make sure the lamp is not plugged into

in the lamp, unthread the bulb from the

an electrical socket.

socket (G) turning counterclockwise to

loosen.

2. If the lamp has been in use, allow it to

cool approximately 5 minutes before

DO NOT allow glass part of the bulb to

proceeding.

strike the shade or any hard surface.

3. To install the bulb (K) in the socket

Please note that in operation, OttLite

(G), thread the base of the bulb into the

bulbs are not dimmable.

socket turning clockwise until snug.

Enjoy your OttLite Cambridge

CAUTION: DO NOT overtighten the

Table Lamp!

bulb. Overtightening the bulb may

This lighting system is designed

make removal difficult or damage the

for use with OttLite type

lamp or bulb.

(style number ED15-S). Use of other

products voids the warranty and

4. To remove a bulb (K) already installed

may result in damage to the lighting

in the lamp, unthread the bulb from the

socket (G) turning counterclockwise to

system.

loosen.

Please note that in operation, OttLite

bulbs are not dimmable.

Enjoy your OttLite

Cambridge Table

Lamp!

This lighting system is designed

for use with OttLite

type

(style number ED15-S). Use of other

products voids the warranty and

may result in damage to the lighting

system.

CAUTION! IMPORTANT SAFETY INSTRUCTIONS:

THIS PORTABLE LAMP HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER) AS A FEATURE TO

REDUCE THE RISK OF ELECTRIC SHOCK. THIS PLUG WILL FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF

THE PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A

QUALIFIED ELECTRICIAN. NEVER USE WITH AN EXTENSION CORD UNLESS PLUG CAN BE FULLY INSERTED.

DO NOT ALTER THE PLUG.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,

FULLY INSERT.

AVERTISSEMENT! IMPORTANTES DIRECTIVES

¡ PRECAUCIÓN! INSTRUCCIONES DE SEGURIDAD

DE SÉCURITÉ:

IMPORTANTES:

CETTE LAMPE PORTATIVE EST MUNIE D'UNE FICHE POLARISÉE (UNE LAME PLUS LARGE QUE L'AUTRE). CE

ESTA LÁMPARA PORTÁTIL TIENE UN ENCHUFE POLARIZADO (UNA DE SUS PATAS ES MÁS ANCHA QUE LA

DISPOSITIF DE SÉCURITÉ DIMINUE LE RISQUE DE CHOCS ÉLECTRIQUES PUISQUE LA FICHE NE S'INSÈRE

OTRA) COMO CARACTERISTICA PARA REDUCIR EL RIESGO DE UNA DESCARGA ELÉCTRICA. ESTE ENCHUFE

DANS LA PRISE QUE D'UN SEUL CÔTÉ. SI ELLE N'ENTRE PAS DANS LA PRISE, INVERSEZ-LA. SI ELLE

ENCAJARÁ EN CUALQUIER TOMACORRIENTE POLARIZADO SOLO DE UNA MANERA. SI EL ENCHUFE NO CALZA

N'ENTRE TOUJOURS PAS, CONTACTEZ UN ÉLECTRICIEN QUALIFIÉ. N'UTILISEZ JAMAIS AVEC UNE RALLONGE

COMPLETAMENTE EN EL TOMACORRIENTE DÉLE LA VUELTA. SI AÚN NO ENCAJA, PÓNGASE EN CONTACTO

SAUF SI LA FICHE S'INSÈRE ENTIÈREMENT. NE MODIFIEZ PAS CE DISPOSITIF DE SÉCURITÉ.

CON UN ELECTRICISTA CALIFICADO. NUNCA UTILICE UNA EXTENSIÓN A NO SER QUE EL ENCHUFE PUEDA

AVERTISSEMENT:

SER TOTALMENTE INSERTADO. NO ALTERE EL ENCHUFE.

POUR ÉVITER LES CHOCS ÉLECTRIQUE, INSÉREZ LE BOUT LARGE

PRECAUCIÓN:

DE LA FICHE DANS LA GRANDE FENTE ET POUSSEZ JUSQU'AU BOUT.

PARA PREVENIR UNA DESCARGA ELÉCTRICA, HAGA COINCIDIR LA PATA

ANCHA DEL ENCHUFE CON LA RANURA ANCHA, INSERTE TOTALMENTE.

¡ PRECAUCIÓN! INSTRUCCIONES DE

AVERTISSEMENT! IMPORTANTES DIRECTIVES

SEGURIDAD IMPORTANTES: