GE SunSmart Manual De Instrucciones

Outdoor
SunSmart
™
DISPLAY SHOWN IN STANDARD "CLOCK" MODE.
Program
- Press to set/view
programming.
Mode/Resume
- Toggle between Auto, Random
(RDM), and Manual modes.
- In programming mode, deletes
a set program.
USE PENCIL OR TOOTHPICK TO RESET ALL SETTINGS.
INSTALLATION:
Wireless Battery Operated Timer
1. On the back of the wireless timer, remove the plastic tab keeping the battery from making connection.
You may need to remove the battery door if the tab doesn't pull out easily.
A. If the clock has not started, remove the batteries and reinstall them following the "+" and "–"
polarities, ensuring they match the marked information within the battery housing.
B. Replace the plastic battery door ensuring that it snaps back into place.
Mounting And Installing The Receiver Module
1. Mount the receiver outlet on a wall near a GFCI receptacle using a nail or screw head. The nail or screw
must extend at least 7/8in. out from the wall. The timer must be mounted at least 2ft. above ground level.
2. Hang the receiver outlet from the eyelet on top of the unit with the receptacles facing downward.
Plug-In Receiver Module
1. Plug in the light or electronic device you wish the wireless timer to control into your receiver module.
2. Plug the receiver module into your wall outlet.
3. Make sure your light/device is turned to the On position. The lamp or device should not turn on.
SETTING THE DATE AND TIME
NOTE: If no buttons are pushed for 30 seconds while in programming mode, the timer will default back to
the clock screen. Push the Time button until you return to the step where the timer reset.
1. Press RESET button on your wireless battery operated timer using a toothpick or a pencil and clear all
settings.
2. Press the Time button once, and the year will be blinking. Press the Up or Down button to set the current
year then press the Time button.
3. The month will be blinking. Press the Up or Down button to set the current month then press the Time
button.
4. The day will be blinking. Press the Up or Down button to set the current day then press the Time button.
5. Daylight Savings Time (DST) needs to be set next. DST with On blinking will be displayed. If your area
observes DST, then press the Time button and move to the next step. If your area does not observe DST,
then set it to Off by pressing the Up or Down button and press the Time button to continue to next step.
NOTE: DST will automatically reset the times in the timer to match the current time change, if DST is set
to On. The default DST time change is 2:00 am, the second Sunday of March, and then the first Sunday in
November.
6. Next step is to set the current time. The hour should be flashing, press the Up or Down button to select
the current hour ensuring that AM/PM is correct then press the Time button.
7. The minute should be flashing, press the Up or Down button to select the current minute then press the
Time button.
SETTING THE SUNSMART™ FEATURE
ALASKA
NORTH
CENTRAL
SOUTH
HAWAII
1. NOR (North) will be flashing on your screen, press the Up or Down button to choose your location.
A. NOR (North)
B. CEN (Central)
C. SOU (South)
2. Press the Time Button once you have chosen your correct location.
3. Your programmed sunrise time will now be on your screen with the time blinking. If the time is correct,
press the Time button and continue to the next step (If the time is not correct, press the Up or Down
button to fine tune the correct time the sun rises in your location then press the Time button).
4. Your programmed sunset time will now be on your screen with the time blinking. If the time is correct,
press the Time button and continue to the next step. (If the time is not correct, press the Up or Down
button to fine tune the correct time the sun rises in your location then press the Time button).
5. Your timer should now be returned to the clock screen showing the current time.
MADE IN CHINA
GE is a trademark of General Electric Company and is under
license by Jasco Products Company LLC, 10 E. Memorial Rd.,
Oklahoma City, OK 73114.
This Jasco product comes with a 1-year limited warranty.
Visit www.jascoproducts.com for warranty details and
product registration.
Questions? Contact us at 1-800-654-8483 between
7:30AM—5:00PM CST.
Wireless Timer System
On/Off- Turns all wireless
receivers within range On/Off
- Returns to Clock Mode when
in programming mode.
Up/Down
- Scroll through
settings options
Time
- Press to set the date/time.
- Press to confirm choices
when programming.
Total ratings for both
outlets:
125VAC 60 Hz:
15A General Purpose
15A Resistive
1000W Tungsten
8.3A Standard Ballast
500VA Electronic Ballast
120VAC 1/4 HP
SETTING THE TIMER ON/OFF PROGRAMS
NOTE: If no buttons are pushed for 30 seconds while in programming mode, the timer will default back
to the clock screen. Push the Program button until you return to the correct program you were setting,
then press the Time button to return to the correct step where the timer reset (you can scroll through all
7 On/Off programs by pushing the Program button).
1. Press the Program button to begin setting the times you wish your connected light or electronic device
to turn On/Off.
2. "-- -- 1 ON" will be on the screen, press the Time button to program your first On program time.
3. The day of the week will be flashing, press the Up or Down button to choose the days you wish this
program to work. Your options are:
A. Monday thru Sunday
B. Each day individually
C. Monday thru Friday
D. Saturday & Sunday
E. Monday, Wednesday & Friday
F. Tuesday & Thursday
4. Press the Time button once you have chosen the days of the week you want to control the device.
5. The hour will now be blinking. You have three options to choose from:
A. Sunset time: Press the Down button once to choose your pre-programmed sunset time or scroll untill
the preset programmed time shows on the screen. If you choose to use the pre-programmed sunset
time, press the Time button and then press the Program button to move to 1 Off program and skip to
step 6.
B. Sunrise Time: Press the Down button a second time to choose your pre-programmed sunrise time
or scroll untill the preset programmed time shows on the screen. If you choose to use the pre-
programmed sunrise time, press the Time button and then press the Program button to move to 1 Off
program and skip to step 6.
C. Custom Time: Pressing the Down button a third time or scrolling with the Up button will let you
manually select any hour and minute desired.
i. If you chose to use a custom time, the hour will be blinking. Keep pressing the Down button to
choose the hour you wish the timer to turn on (keeping in mind AM/PM). Press the Time button
once you have selected your hour.
ii. The minute will now be blinking, press the Up or Down button to choose the minute then press the
Time button.
iii. Press the Program button again to program your first Off program time.
6. The screen should read "-- -- 1 OFF". Repeat the previous steps above for choosing your days of the week
and program time.
7. Repeat these steps for up to 7 different programs setting as many On/Off cycles as desired. At any time,
push the On/Off button to complete programming and return to clock mode.
DELETING A PROGRAM
Press the Program button until you get to the program you would like to delete. Press the Mode/Resume
button and the program setting will be deleted.
TIMER MODE OPTIONS
• AUTO: Timer functions using all programs you have set.
• RDM (Random): Timer uses all programs you have set +/-30 minutes of On/Off times giving your home a
more lived in look while away.
• None (Manual mode): Timer does not use programs at all and is only on manual mode.
USING TIMER AS A REMOTE CONTROL
1. Simply press the On/Off button to override timer programs to turn your lights or devices On/Off.
2. If timer is in AUTO mode, it will follow the next timer program setting to turn your light or device On/Off.
3. If the timer is in RDM (Random) mode, it will follow the next timer program setting to turn your light or
device On/Off +/- 30 minutes.
4. If the timer is in Manual Mode (Blank on your screen not showing AUTO or RDM), then the light or device
will stay On/Off until you change your timer mode option or you manually use the On/Off button again.
This device complies with part 15 of the FCC rules and with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause
undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions may cause harmful
NORTH
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encourage to try to correct the
CENTRAL
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
SOUTH
• Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter.
See www.jascoproducts.com for troubleshooting and frequently asked questions (FAQs).
BATTERY-OPERATED TRANSMITTER
CAUTION
BATTERIES MAY LEAK HARMFUL LIQUIDS OR IGNITABLE
MATERIALS OR EXPLODE CAUSING INJURY AND
PRODUCT DAMAGE
• DO NOT MIX OLD AND NEW OR OTHER BATTERY TYPES
• REPLACE ALL BATTERIES AT THE SAME TIME
• REPLACE FULLY DISCHARGED BATTERIES IMMEDIATELY
• REMOVE BATTERIES IF PRODUCT IS TO BE UNUSED FOR
AN EXTENDED PERIOD OF TIME.
26683 VERSION 01
12/04/14
AC POWERED RECEIVER OUTLET
WARNING
RISK OF ELECTRIC SHOCK
• DO NOT USE WITH AN EXTENSION CORD
• PLUG DIRECTLY INTO A GFCI PROTECTED
ELECTRICAL OUTLET
• UNPLUG BEFORE CLEANING
• FULLY INSERT PLUG
• KEEP CHILDREN AWAY
RISK OF FIRE
• DO NOT USE TO CONTROL APPLIANCES THAT
CONTAIN HEATING ELEMENTS (COOKING
APPLIANCES, HEATERS, IRONS, ETC.)
• DO NOT EXCEED ELECTRICAL RATINGS
• RECEIVER OUTLET MUST BE MOUNTED
I N A VERTICAL POSITION WITH THE
R ECEPTACLE FACING DOWNWARD AND WITH
T HE RECEPTACLE AT LEAST 2 FEET ABOVE THE
G ROUND LEVEL
• NOT FOR WATER IMMERSION.
GE53101R